background image

Quick Access Cassette System

Unlike other competitive automatic pool cleaners, the Zoom has the Quick Access Cassette System. This unique feature allows almost
instantaneous access to the one moving part –  the Diaphragm.

Large foreign objects, such as children’s toys, tree branches and rocks, should be removed manually from your pool prior to operating
an automatic pool cleaner. In the event a foreign object does not get manually removed and a blockage occurs, the Quick Access
Cassette System allows you the opportunity to remove the blockage or check the Diaphragm for damage in minutes at poolside.

DIAPHRAGM REMOVAL

Holding the hull assembly in one hand, unscrew the cassette (Step 1) and remove (Step 2). Holding the cassette at each end, unscrew
the cassette pipe from the Diaphragm chamber two full turns (Step 3). Grasp the lip of the Diaphragm and pull the Diaphragm out
(Step 4). The inner pipe will be attached and will make a loud noise. Pull the Diaphragm off of the inner pipe, leaving the retaining
ring on the Diaphragm (Step 5), and inspect for blockage or cuts. Remove blockage and rinse. Do not use sharp objects as damage to
Diaphragm may occur. If replacement parts are needed, contact technical service at 1-888-786-7797 for an authorized warranty station.

DIAPHRAGM ASSEMBLY

Prior to reinstalling the Diaphragm, rinse the Diaphragm and inner extension pipe thoroughly to remove any grit or algae. Attach the
Diaphragm to the inner extension pipe using the retaining ring (Step 6). Slide the inner extension pipe into the Diaphragm chamber. Pressing
on the underside of the Diaphragm’s ridges, push the Diaphragm into the chamber (Step 7). Holding the cassette at each end, tighten the
cassette pipe until snug, but do not overtighten. (Step 8). Insert the cassette assembly into the hull assembly and tighten (Step 9).

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

To maintain quality, performance and increase the lifespan of your Zodiac Zoom, please do the following:

1.

Thoroughly clean the skimmer basket, pump basket and pool filter on a regular basis. 

Always disconnect the hose from the

skimmer before backwashing.

2.

REMOVE THE CLEANER BEFORE SUPER CHLORINATING OR ADDING POOL CHEMICALS.

Reinstall the Zodiac

Zoom when the imbalance is corrected or after a minimum of 4 hours from super chlorination. Chemical damage is not covered
under warranty.

3.

NEVER COIL THE HOSE

when the cleaner is removed from the pool. A coiled hose can be straightened with hot water or by

laying it on a warm pool deck for several hours.

INCORRECT

CORRECT

X

4. Remove disc and store it flat during the off-season. Store the cleaner head in a warm and dry place.

ZODIAC ZOOM

CARE AND MAINTENANCE

Step 9

Summary of Contents for Zoom













Reviews: