Zodiac PX50 MD12 Instructions For Installation And Use Manual Download Page 25

Page: 25 / 36

EE13

Electrical protection

The data is incorrect.

Check the compressor.

The water flow rate is insufficient.

Check the water flow rate.

The voltage is unstable.

Check the power supply voltages.

PFC failure.

EE14

Abnormal IPM module operating

temperature

The power supply is incorrect.

Check the power board.

The fan motor is defective or the

propellers are broken.

Check the fan speed

Check the propellers.

EE15

IPM module high temperature protection

The power supply is incorrect.

Check the printed circuit board.

The fan motor is defective or the

propellers are broken.

Check the fan speed

Check the propellers.

EE16

PFC module protection

The data is incorrect.

Check the printed circuit board.

The fan motor is faulty.

Check the fan speed.

The propellers are broken.

Check the propellers.

The voltage is unstable.

Check the voltage.

EE17

DC fan error

The fan motor is faulty.

Check the fan motor.

The printed circuit board is faulty.

Replace the printed circuit board.

The propellers are faulty.

Check the propellers.

EE18

Abnormal PFC module operating

temperature

The printed circuit board is faulty.

Replace the printed circuit board.

Check the fan speed.

Check the propellers.

EE19

PFC module high temperature protection

The power supply is incorrect.

Check the printed circuit board

The fan motor is faulty.

Check the fan speed.

The propellers are broken.

Check the propellers.

The connections to the power board

are loose.

Check the connections, tighten

the screws.

EE20

Power supply error

The power supply varies too much.

Check the power supply voltage.

EE21

Programme error.

The compressor is losing power,

operating at an irregular speed.

Check the printed circuit board
Reload the programme

Programme error.

Impurity in the compressor.

EE22

High voltage protection

The power supply is incorrect.

Replace the printed circuit board.

The power board is faulty.

Replace the printed circuit board.

EE23

Compressor start-up error

The power board is faulty.

Check the printed circuit board.

Accumulation of liquid and gas.

Check the power supply voltages

The voltage is unstable.

Check the voltage.

Summary of Contents for PX50 MD12





































Search results

Summary of Contents for PX50 MD12

Reviews:

Related manuals for PX50 MD12

Brands by name

Popular brands

Zodiac PX50 MD12, Instructions For Installation And Use Manual

Search results

Summary of Contents for PX50 MD12

Reviews:

Related manuals for PX50 MD12

Brands by name

Popular brands