background image

Section 2.  Getting Started

2.1  General Specifications 

The general specifications for the cleaner are as follows: 

Control box 

supply  

voltage 

 

220-240 VAC, 50 Hz; short circuit-proof 

safety isolating type 

Supply voltage

30 V DC

Installed load

150 W max

Cable length

15m (50 ft)

Cleaner size 

(WxDxH)

41 x 42 x 25 cm

Weight of Cleaner

9 kg

Filtration 

All-purpose filter canister

Cycle lengths

Variable programming

 

This cleaner is a double-insulated product. A double-

insulated electrical appliance is one which has been 

designed in such a way that it does not require a safety 

connection to ground. The basic requirement for 

double-insulation is that no single failure will result in 

dangerous voltage becoming exposed so that it might 

cause an electric shock and that this is achieved by 

having two (2) layers of insulating material surrounding 

live parts or by using reinforced insulation. Therefore, 

devices having double-insulated construction, such as 

this cleaner, do not require a grounded (three-prong) 

plug.

2.2 Unpacking

The packaging should contain the following items:
• Zodiac

®

 Robotic Cleaner

•  Floating Cable
•  Control box

When unpacking the cleaner and its components:
•  Check to make sure each component is in the box.
•  Check cleaner and components for damage during 

transport.

•  If there are missing parts or damage, contact  

Zodiac Technical Support:  1300 763 021

2.3  Cleaner Control box

SURFACE CONTROL SYSTEM

1

           

          

3

           

4

ROUGH

SMOOTH

Select Cleaning Surface

• Floor

• Floor and Walls

Start/Stop 

Cleaner

Cleaner Error  

Indicator

Surface Control 

System (SCS) 

for wall cleaning 

(rough to smooth 

surfaces)

LEDs indicating 

pump strength for 

SCS

H0446500_REV A

Summary of Contents for CyclonX CX20

















Reviews: