background image

SECTION 1 – INSTALLATION

2

STEP 1: Preparing your pool and filtration system

IMPORTANT

The filtration system must be operating at its MAXIMUM WATER FLOW 
before you install your BARACUDA

®

GENIUS

®

3000, otherwise you will have 

to re-adjust your BARACUDA

®

GENIUS

®

3000 after cleaning the pool filter.

Installation is easy if you follow these simple preliminary steps:

1. Empty the weir basket.

2. Clean the pump basket.

3. Backwash the filter until the sight glass is clear.

4. Adjust all return jets (whether your pool has one, two or more) to point

downwards and towards each other so that you DO NOT see a circular
water flow or waves on the surface of your pool.

STEP 2: Assembling the disc to your Genius

®

3000

A

A

B

B

A

B

C

Diagram 1

1. Viewed from underneath the unit, the fins

on the Disc should point downwards and
the words Baracuda and the Zodiac logo
should not be visible.

2. Beginning at one corner of the flat front

section of the FlexiFoot, stretch the Disc
around to the other corner, until the disc
is held in place by the FlexiFoot.

Pull Disc under edge of FlexiFoot.

Disc

FlexiFoot 

(factory fitted)

Diagram 2

(Viewed from side)

2. Position the Disc underneath
the Disc retaining Lug (C)

Diagram 3

(Viewed from front)

3. Ensure both the Disc Pillars (A) are located
in front of the Stop blocks (B)

NB:The Disc must not rotate more than ± 4 mm once it has been installed.

Summary of Contents for BARACUDA Genius 3000





















Reviews: