background image

BG2000 Series Barrier Gate (APP Version)                             

                      User Manual 

P a g e

 | 4 

 

        Copyright©2022 ZKTECO CO., LTD.  All rights reserved. 

Document Conventions 

Conventions used in this manual are listed below: 

GUI Conventions 

For Software 

Convention 

Description 

Bold font 

Used to identify software interface names e.g., OKConfirmCancel.  

Multi-level menus are separated by these brackets. For example, File > Create > 
Folder. 

For Device 

Convention 

Description 

< > 

Button or key names for devices. For example, press <OK>. 

[ ] 

Window  names,  menu  items,  data  table,  and  field  names  are  inside  square 
brackets. For example, pop up the [New User] window. 

Multi-level  menus  are  separated  by  forwarding  slashes.  For  example, 
[File/Create/Folder]. 

 

Symbols 

Convention 

Description 

 

This represents a note that needs to pay more attention to. 

 

The general information which helps in performing the operations faster. 

 

The information which is significant. 

 

Care taken to avoid danger or mistakes. 

 

The statement or event that warns of something or that serves as a cautionary 
example. 

 

 

Summary of Contents for BG2000 Series



































Reviews: