background image

Page 24 of 28                   801912UK - Commercial Boiling, chilled and sparkling user manual - Sept 2016- v2.04

Filter maintenance

Air 

Filter

Slide to remove

Warning: If the HydroTap

®

G4 

is switched off for a long period 

of time (e.g. more than a 

weekend), run water through the 

chilled water outlet for at least 5 

minutes before consumption.

• 

Caution. 

A

 small amount of water will drip as the cartridge is 

removed.

• 

Do not tilt the cartridge as water may spill from it if tilted.

• 

Unpack replacement cartridge and remove sanitary cap, write today’s 

date where shown on the label. 

• 

Avoid touching the filter o-rings and filter opening as this may cause 

bacterial contamination of the cartridge.

• 

Moisten the o-rings with water, align the front cartridge label to the 

left (as shown in the “insert filter” diagram below), and push the new 

cartridge up into the filter head. 

• 

Turn the cartridge a quarter turn anticlockwise until the cartridge comes 

to complete stop and is locked into position, with the front label facing 

forward.  

• 

Initiate the filter flush programme by scrolling through the menu screen 

(see page 13).

• 

When completed, wipe up any spills and dispose of spent filter cartridge 

and packaging thoughtfully.

• 

Close the door to secure the appliance.

• 

Adjust the filter settings in Section G (see page 19) litres and days. 

Air Inlet Filter

The HydroTap

®

G4 air filter is conveniently located on the outside of the 

condenser. The filter screen is a sliding fit in the plastic housing on the left 

hands side of the Command-Centre

TM

. The screen may be removed for 

cleaning by sliding it forward. This needs to be inspected at least quarterly, 

cleaned and replaced if damaged.

Note

 For best performance the unit should only be operated with a clean 

air filter screen, correctly fitted in place. Maintain at least a 50mm air gap 

in front of the screen at all times. Take care not to allow cloths or other soft 

materials to accidentally block the air inlet.

Summary of Contents for 801912UK





























Reviews: