background image

804545 03.17 1.00

 

Page 3 of 24

Read These Warnings First

Please read all installation requirements, installation procedures 

and precautions before installing any Zip Autoboil instant boiling 

water heater.
Never attempt to install any Zip Autoboil instant boiling water heater 

without reading all of the applicable instructions.
In some hard water areas where mineral scale accumulation in 

the boiling chamber of the Zip Autoboil may become a problem, 

consideration should be given to the maintenance required. A 

suitable form of water treatment may be necessary.
The cold water supply to this appliance must be potable and fall 

within your local authority’s guidelines.
All plumbing connections must be made in accordance with local 

regulations.
The Zip Autoboil instant boiling water heater is not intended for use 

by young children or infirm people without supervision. 
Young children should be prevented from having access to ensure 

that they are not able to use or play with the heater.  
This appliance must be earthed. If the power supply cord is 

damaged it must be replaced by a Zip authorised agent or a qualified 

electrician. 
Do not remove the cover of the heater under any circumstances 

without first isolating the heater from the power supply.
Do not use strong, corrosive or abrasive cleaners to clean the case 

of the heater.
Frost protection: If this heater is located where ambient air 

temperature could fall below 5ºC when the heater is not in use, do 

not turn off the appliance electrically. This safeguide does not offer 

the same protection to the connecting pipework and fittings.
The ambient temperatures this unit must operate within is 5ºC - 

50ºC.
This heater is intended only for indoor use and should never be 

installed outdoors or be exposed to the elements of nature.
This unit must not be positioned in an area that may be cleaned by a 

water jet. This unit must not be cleaned by a water jet.

Before installing, ensure that the following are available:
a)  Sufficient space to position the heater so there is at least 100 mm  

  clearance above the heater for service access, 150 mm to its left 

and 

20 mm to its right – the tap outlet must be positioned at least 

300 mm above a draining board or drip tray.

b)  Standard 220- 240 volt power cable positioned as shown on the 

paper mounting template for connection from the rear of the 

heater to the terminal block within the heater, OR a standard 10 

amp 220- 240 volt power outlet on the wall within 1500 mm of the 

heater. This switch must provide all-pole disconnection and a 

contact separation of at least 3 mm installed in accordance with 

wiring rules, see Step 3 - 3.3). 

Installation Requirements

Summary of Contents for 303051

























Reviews: