Zionair SB22A Assembly And User Instructions Manual Download Page 13

12 

 

5.

 

Maintenance 

WARNING! Before performing maintenance, remove the plug form the power source, failure to 
heed this instruction may cause electrocution. Close the valve of the compressed air supply. 

Check before each use 

Check the sandblasting cabinet previous to each use for damaged and/or deformed parts. Check all 
hoses for wear and tear and check if the nozzle is not too worn. Check if the dust extractor works 
well, clean it if necessary, finally also check if the doors/covers still close properly. In case of a 
malfunction/defect, do not use the sandblasting cabinet until it has been repaired. 

Possible problems and causes 

1.

 

Check the nozzle every 10-12 hours, in case it is worn unevenly, turn it ¼ stroke every 10 
hours. 

2.

 

In case the grit is clotting, this means there is moisture in the compressed air or there is 
moisture/oil in the system. This leads to clogging and an uneven spray. Always place an air 
unit/air dryer in the system. It could also be that there is too much debris in the grit, this can 
be solved by filtering/replacing the grit. 

3.

 

When the spray is often disrupted, place a thumb (WITH GLOVES ON) over the nozzle and 
(press firmly) and depress the foot pedal for a few seconds. Now the air blows back into the 
suction hose, which can dissolve possible obstructions. 

4.

 

Regularly check for leakages/obstructions in the compressed air supply. Adjust the pressure 
to 5.5 bar on the air regulator, now press the foot pedal and check for sudden pressure drop. 
If this is the case it means the compressed air supply is obstructed, this can be caused by: 
-

 

Diameter of air hose too small 

-

 

Blocked coupler/pressure regulator 

-

 

Blocked/kinked hose 

-

 

Distance between compressed air supply and sandblasting cabinet is too big 

ADVICE: The diameter of the air hose should be at least ½“. 

5.

 

In case of poor visibility inside the cabinet by excessive dust, this could have the following 
causes: 
-

 

Air inlet top left of the pressure regulator is blocked 

-

 

Dust extractor is full and is to be cleaned/emptied 

-

 

Filter of dust extractor is full/polluted by moist/oil 

-

 

Grit is no longer good (too fine) 

6.

 

Poor visibility inside the cabinet can also be caused by damaged protective foil, which is 
placed over the viewing glass. This can easily be replaced by new foil. When the glass itself is 
damaged, replace it by safety glass with the same thickness and measurements, you can get 
this at your Zionair retailer. 

Cleaning the dust extractor (not inlcuded) 

Check the dust extractor after every 5 hours, remove dust by means of compressed air or vacuum 
cleaner and removed clogged debris to ensure a proper functioning of the extractor. 

Summary of Contents for SB22A















Reviews: