background image

Step 19 

 

 

1.

 On your remote press 

Menu,

 then go down to 

System Configuration. 

Then use the right arrow key, toggle to the right and then 

down to 

System Setup

 

2. 

Toggle down to 

TIME

 (using the down arrow key on your remote). 

3.

 Toggle right to switch Summer Time to 

ON*

 

(If it is not currently daylight saving time, then switch to 

OFF

EXIT

 and return back to normal TV.  

 
*PLEASE NOTE: 

For software versions 6C and later, there is no option for Summer Time and the time may need to be set manually. 
You are Done restoring all the channels back into your Zinwell ZMX7500 or DSE G7500 

Important Information regarding the Electronic Programme Guide (EPG):

 

You will 

not

 be able to load the EPG (on-screen TV listings via the Electronic Programme Guide) from BravoPlus1, PRIME and 

Duke+1. i.e. any channel that you have just manually added 
 
You will HOWEVER be able to access the EPG of these channels from another channel e.g. TV1 TV2 etc 
 
 

If you have a Widescreen TV, here are the additional steps to adjust your ZMX-7500 or DSE-7500 for a wide screen picture 

1.

 

Press 

Menu

 

2.

 

Select 

System Configuration

 

3.

 

Select 

System Setup

 

4.

 

Select 

TV

 

5.

 

Select 

Aspect Ratio

 

6.

 

Change the Aspect Ratio to 16:9 (using the left or right arrow keys) 

7.

 

Press Ok then Exit twice to save the new setting. 

 

An older version of these instructions may also be available online at:  

http://freeviewforum.co.nz/rescan/zinwelldseguide-1

 

 

How to use the rename guide on the DSE7500 and Zinwell ZMX7500? 

 
The window that pops up to rename a channel or service may seem complicated at first, this quick guide will 
show you how this works using your remote: 
You will see a screen similar to that below (Name will vary e.g. Maori Television, FOUR, New Satellite 
etc...)  
 

 

Summary of Contents for Freeview ZMX-7500














Reviews: