background image

11

8  Accessories

INFORMATION

If any accessories not sold or authorized by Zimmer GmbH are used, the function of the product cannot be 

guaranteed. Zimmer GmbH accessories are specifically tailored to the individual products.

 

For optional accessories and those included in the scope of delivery, refer to our website.

8.1  Sensors

Example image of a combination consisting of 

a stationary part, loose part and storage 

station.

5

5

6

The sensors of the storage station check 

whether the loose part is present in the storage 

station and the locking is ensured.
The sensor of the stationary part checks 

whether the loose part and stationary part are 

connected.

5

Sensor of storage station

6

Sensor of stationary part

9  Transportation/storage/preservation

 

Transport and storage of the product must be done only with the original packaging.

 

If the product has already been installed on the superordinate machine unit, care must be taken during transport to 

ensure that no unexpected movements can occur. 

 

Before commissioning the product and after transport, check all power and communication connections as well as 

all mechanical connections.

 

If the product is stored for an extended period, the following points are to be observed:

 

Keep the storage location as dust-free and dry as possible.

 

Avoid temperature fluctuations/observe and adhere to the temperature range.

 

Avoid wind/drafts/water condensation formation.

 

Cover the product with a weatherproof, tear-resistant foil to prevent dust.

 

Pack the product and do not expose it to direct sunlight during storage.

 

Clean all components. There must be no soiling left on the components.

 

Visually inspect all components.

 

Remove all foreign substances.

 

Properly remove potential corrosion spots.

 

Close electrical connections using suitable covers.

INSTALLATION AND OPERATING INSTRUCTIONS:

FWR

DDOC01406 / -

EN / 2022-05-10

Zimmer GmbH • Im Salmenkopf 5 • 

 77866 Rheinau, Germany • 

 +49 7844 9138 0 • www.zimmer-group.com

Summary of Contents for FWR Series
























Reviews: