USER MANUAL ZHS19
DOOR AND WINDOW SENSOR
ZHS19
MANUFACTURER INFORMATION
Dear Customer,
should you require technical advice and
your retailer could not help please contact
our technical support.
Schwaiger GmbH
Würzburger Straße 17
90579 Langenzenn
Hotline: +49 (0) 9101 702-199
www.schwaiger.de
6. Network removal of the device
Put the Gateway into removal mode by choosing
„Home setup“ in the main menu and then click on
„Add device“ (See images on the left). Then reset
the device to default settings.
7. Reset to default settings
Press the networking button for 5 seconds until
the green LED starts to flash slowly.
Note: For network inclusion, the sensor must always be in the factory state.
LED indicator of devices
Network inclusion
Press the networking button for 2
seconds until the green LED starts to flash
(two times per second)
Network removal / Reset
The green LED flashes 6 times
(once per second)
Alarm (anti-tamper key)
The red LED flashes once
LED
indicator
Sensor
Magnet
Anti-tamper key
Technical data
Working voltage
DC 3 V (2 x AAA battery)
Static current
≤ 5 µA
Alarm current
≤ 35 mA
Detecting distance
< 15 mm
Range
about 15 m (depending on building
structure)
Working environment
-10°C ~ +50°C
Transmission power
<1 mW
Frequency range
2405-2480 MHz
Sensor dimension
76 x 36.6 x 16.5 mm
Magnet dimension
76 x 13.9 x 16.5 mm
Read these instructions before installing!
Do not use the device in any manner other than that specified in the manual. The
manufacturer disclaims any guarantee if the device is used improperly.
CAUTION!
The device is not a toy. Keep away from children and pets. The device cannot be repaired
and must not be opened.
Disposal
Do not dispose of batteries or electric and electronic devices in the normal house-
hold waste. The consumer is legally obliged to return electrical and electronic de-
vices and batteries that are at the end of their useful life to the point of sale or
public collection points that have been set up for this purpose. Legislation in the
country of use governs individual details regarding disposal. batteries should be disposed
of separately. The symbol on the product, the user guide or the packaging indicates this
legal requirement.
Declaration of conformity
Schwaiger GmbH hereby declares that the specified radio equipment product complies
with Directive 2014/53/EU and other applicable directives. The complete EU declaration
of conformity is available online at: http://konform.schwaiger.de
Explanation of symbols
CAUTION!
This symbol indicates a danger.
NOTE:
This symbol indicates important points.
3. Networking button
Press the networking button (within the hole) for 2 sec-
onds until the green LED starts to flash fast, then let
go. The device will be detected and included into the
network.
4. Installation of Door/Window Sensor
Select a place for installation. Remove the protective
cover and stick the bracket to the place desired. The
sensor should be installed at an immovable place, e.g.
a door frame. The magnet can be installed on either
side of the sensor at the movable part of the location
(e.g. door panel, see example).
The distance between sensor and magnet should not
exceed 15 mm.
5. Attach the sensor to the bracket
Congratulations and thank you for purchasing the Schwaiger
ZHS19 product. Below you will find useful operating guidelines.
This is a smart door and window sensor which is based on the ZigBee Wireless Networking
technology. It has a very low power consumption which makes for longer battery life. The
sensor detects whether a door or window is opened or closed. Thanks to the dual sensor
design, installation is even more flexible and adaptable.
Network inclusion
1. Remove the protective
battery cover
2. Put the Gateway into inclusion mode
Network inclusion of the sensor
Put the Gateway into inclusion mode.
Remove the protective battery cover, press the networking button for 2
seconds until the green LED starts to flash fast.
Please pay attention to the fact that during network inclusion, the distance
between sensor and Gateway may not exceed 0.5 m.
ZHS19
