background image

1 General notes

Compliance with the following instructions is mandatory to ensure the functionality and 
safety of the product. If the following instructions given especially but not limited for 
general safety, transport, storage, mounting, operating conditions, start-up, mainte-
nance, repair, cleaning and disposal / recycling are not observed, the product may not 
operate safely and may cause a hazard to the life and limb of users and third parties.
Deviations from the following requirements may therefore lead both to the loss of the 
statutory material defect liability rights and to the liability of the buyer for the product that 
has become unsafe due to the deviation from the speci

cations. 

1.1 Structure of the operating instructions

Before installation and start-up, read this manual carefully to ensure correct use!
We emphasize that these operating instructions apply to speci

c units only, and are in 

no way valid for the complete system!
Use these operating instructions to work safely with and on the device. They contain 
safety instructions that must be complied with as well as information that is required for 
failure-free operation of the device.
Keep these operating instructions together with the device. It must be ensured that all 
persons that are to work on the device can refer to the operating instructions at any time.
Keep the operating instructions for continued use. They must be passed-on to all 
successive owners, users and 

nal customers.

1.2 Target group

The operating instructions address persons entrusted with planning, installation, start-
up, maintenance and servicing, who have the corresponding quali

cations and skills for 

their job.

1.3 Exclusion of liability

Concurrence between the contents of these operating instructions and the described 
hardware and software in the device has been examined. It is still possible that non-
compliances exist; no guarantee is assumed for complete conformity. To allow for future 
developments, construction methods and technical data given are subject to alteration. 
We do not accept any liability for possible errors or omissions in the information con-
tained in data, illustrations or drawings provided. 
ZIEHL-ABEGG SE is not liable for damage due to misuse, incorrect use, improper use 
or as a consequence of unauthorized repairs or modi

cations.

1.4 Copyright

These operating instructions contain copyright protected information. The operating 
instructions may be neither completely nor partially photocopied, reproduced, translated 
or put on data medium without previous explicit consent from ZIEHL-ABEGG SE. In-
fringements are liable for damages. All rights reserved, including those that arise through 
patent issue or registration on a utility model. 

Operating Instructions 

NETcon

 A-G-102ANE

General notes

L-BAL-E156-GB 2105 Index 004

Part.-No. 

4/32

Summary of Contents for NETcon A-G-102ANE

































Reviews: