Zida VCTnet AirXpress UC11B Installation And Getting Started Manual Download

Page: 8 / 53

4 Windows

Installation

This section describes the procedures for installing the VCTnet AirXpress UC11B

Wireless Network Adapter under Windows 98, ME, 2000, and XP operating systems.

Before You Start

Before the installation, please check your system in advance and ensure it meets

the minimum requirements as described below:

- Processor: Intel Celeron / Pentium II /Pentium III / Pentium IV; AMD Duron /

Athlon or above

- Operating System: Microsoft Windows 98 / ME / 2000 / XP/ Linux
- System memory: 32MB minimum

- Hard Drive Free Space: 5MB

Note: To prevent potential problems during installation, please run the

installation tool from the CD to finish the driver installation before you
plug the UC11B wireless network adapter into the computer.

To use the UC11B, the system must be has an available USB port. All drivers

and the supporting software for the UC11B must be installed and configured.

Ask your system administrator for the following information, which you may need

during driver installation:

•

Your Wireless LAN SSID.

•

Your computer’s unique client name and workgroup name

•

For your network account, your user name and password.

•

Your IP address, gateway address, and subnet mask, if you’re not using a

DHCP server.

Every computer on a network is identified by a unique network address. There

are two methods to assign network addresses to computers on a TCP/IP network:

•

Static IP addressing

•

Dynamic IP addressing (DHCP)

Summary of Contents for VCTnet AirXpress UC11B






















































Search results

Summary of Contents for VCTnet AirXpress UC11B

Reviews:

Related manuals for VCTnet AirXpress UC11B

Brands by name

Popular brands

Zida VCTnet AirXpress UC11B, Installation And Getting Started Manual

Search results

Summary of Contents for VCTnet AirXpress UC11B

Reviews:

Related manuals for VCTnet AirXpress UC11B

Brands by name

Popular brands