21
hurrimix
The reference figures are present on pages 3, 4, 5 and 6 of this manual and in the product Quick Guide.
EN
9.2
TROUBLEShOOTING
FAULT
When pressing the START button, the mixer does not work.
CAUSE
1. The plug is not correctly inserted.
2. The main switch was not turned on.
3. The ON/OFF button has not been pressed.
4. The lid was left open.
5. None of the above.
REMEDy
1. Connect the plug properly to the mains.
2. Turn on the switch placed on the rear of the mixer.
3. Press the On button placed at the left of the display.
4. Close the door properly.
5. Contact the Authorised After Sales Centre.
FAULT
Clear noises or vibrations when mixing.
CAUSE
1. The mixing container is too full.
2. The mixing container is empty.
3. Powder and water leak during mixing.
REMEDy
1. The total content should never exceed 100 g.
2. Never activate the device when the container is empty.
3. Always ensure that the mixing container is closed. Ensure that
the cover is not damaged. Do not exceed the maximum quantities.
10. ATTAChMENTS
10.1 EC DECLARATION OF CONFORMITY
The Manufacturer:
Zhermack S.p.A.
Via Bovazecchino, 100
45021 Badia Polesine • RO • Italy
Tel. +39 0425 597611 • Fax +39 0425 53596
Declares that the equipment described below:
hurrimix
Conforms to the legislative dispositions established in the following
laws:
EC Directive 2004/108 EC (EMC Directive) and subsequent
amendments.
EC Directive 2006/95 (Low Voltage Directive) and subsequent
amendments.
It is highlighted that Manufacturer’s liability for damage caused by
faulty products expires after 10 years from the date in which the
Manufacturer put the products on the market as envisioned by the
85/374/EEC Directive and Presidential Decree 224/1988.
Badia Polesine, 15/06/2012
Paolo Ambrosini
General Manager
10.2 WARRANTY CERTIFICATE AND IDENTIFICATION FORM
1. With this document the Manufacturer certifies that the product
has been built correctly, top quality materials have been used and
all inspections necessary for compliance with European Community
Directives have been performed. The product is covered by a
warranty period of 36 months from the date of delivery to the user.
Proof of this date is provided from the purchase document and the
copy of the identification form. These documents must be shipped
to the After-Sales Centre with the equipment. Persons wishing
to make use of the warranty must inform of the fault within 8
days of its discovery for the effects and purpose of art. 1495 of
the Civil Code. The warranty is limited to replacement or repair
of individual components or pieces with manufacturing defects
and does not cover costs related to transfer of technical staff,
transport, packaging etc. Breakdowns, faults or damage deriving
from poor maintenance, incorrect power supply, negligence,
inexperience and other causes not imputable to the Manufacturer
and parts subject to normal wear are not covered by the warranty.
The warranty does not cover breakdowns caused by failure to
carry out routine maintenance due to customer negligence. This
warranty does not provide for any reimbursement for direct or
indirect damages of any kind caused to persons or objects due to
equipment inefficiency.
2. The warranty is automatically rendered null and void whenever
the equipment is repaired, modified or tampered with by the
purchaser or unauthorised third parties. The liability for damage
caused by faulty products expires after 10 years from the date in
which the Manufacturer put the products on the market, after
this time it becomes the user’s responsibility, as envisioned by the
85/374/EEC Directive.
3. To have work carried out under warranty the purchaser
must only contact the dealer, Manufacturer-authorised after-sales
centres or the Manufacturer itself. The warranty gives the right
for free replacement of faulty parts. It does not, however, give the
right for replacement of the entire equipment.
4. In the case of disputes regarding application of the warranty,
quality or conditions of the equipment delivered, the purchaser
cannot suspend or delay total payment or payment of the
instalments.
5. No reimbursement can be requested by the purchaser for loss
of production.
6. The warranty is rendered null and void if:
a. The equipment is damaged by a fall, exposure to fire, spilt
liquids, lightening, natural disasters or, however, causes not
imputable to manufacturing defects.
b. Incorrect installation.
c. Incorrect mains connection (incorrect power supply nominal
voltage) or suitable protection devices have not been installed.
d. The serial number has been removed, cancelled or altered.
7. The components to be replaced under warranty, must be
returned to Zhermack S.p.A. which will then send the appropriate
spare parts. Any changed parts that are not returned will be
charged.
8. The Manufacturer and the Dental Deposit do not have to supply
replacement equipments during the repair period.
9. For tax purposes spare parts will only be provided under
warranty where the relevant limitations set out in the terms and
conditions of the warranty are respected.
10. For any other eventuality not provided for by this Warranty
Certificate and the regulations, consult the Italian Civil Code.
11. Invoices for labour, travel and call-out must be paid on their
receipt.
12. The manufacturer and the dealer will comply with all data
processing laws in force, including those relative to safety measures
and in compliance with the specifications given in the data
processing information sheet.
IDENTIFICATION FORM
Equipment Model:
..................................................................................................
Equipment Serial Number:
..................................................................................................
Purchaser:
..................................................................................................
Address
..................................................................................................
Town/Post Code:
..................................................................................................
Tel:
..................................................................................................
Tax Code/VAT Number:
..................................................................................................
Dealer:
..................................................................................................
Purchaser’s Signature:
..................................................................................................
