zewa UAM-880 User Manual Download Page 15

Page: 15 / 18

Authorized Component

please use the ZEWA authorized

adapter(Not included).

BLJ06L060100P-U

100-240V 50-60Hz,0.2Amax

6V 1000mA

Adaptor
Type:

Input:
Output:

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not

expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will

not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more

of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for

an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

FCC Statement

FCC ID:OU9TMB995-BS

Contact Information

For more information about our products or online support, please visit www.zewa.com.

To contact our customer service, please call 888-993-3592 or [email protected].

Manufactured for Zewa, Inc.

12960 Commerce Lakes Drive#29

Fort Myers, FL 33913 USA

www.zewa.com

Toll Free Customer Service:

1-888-993-3592

[email protected]

AUTHORIZED COMPONENT

COMPLIED STANDARDS LIST

Summary of Contents for UAM-880



















Search results

Summary of Contents for UAM-880

Reviews:

Related manuals for UAM-880

Brands by name

Popular brands

zewa UAM-880, User Manual

Search results

Summary of Contents for UAM-880

Reviews:

Related manuals for UAM-880

Brands by name

Popular brands