Zetor PROXIMA PLUS 2011 Series Operator'S Manual Download Page 45

Page: 45 / 204

GETTING TO KNOW THE TRACTOR

G154 E155

LEVER OF SWITCHING ON REAR
OUTPUT SHAF DRIVE

Shifting can be carried out when the trac-

tor is in standstill by pulling up or pushing

down the lever.

a -

Independent rpm of the output

shaft drive-

- Speed depends on speed of

the engine.

n -

Neutral

b -

Dependent speed of the output

shaft speed through a gearbox.

- Speed depends on the en-

gaged gear.

LEVER OF HAND BRAKE AND HITCH
FOR SINGLE-AXLE TRAILER

1. Hand brake lever.

2. Lever of the single-axle trailer hitch

control.

Summary of Contents for PROXIMA PLUS 2011 Series













































































































































































































Search results

Summary of Contents for PROXIMA PLUS 2011 Series

Reviews:

Related manuals for PROXIMA PLUS 2011 Series

Brands by name

Popular brands

Zetor PROXIMA PLUS 2011 Series, Operator'S Manual

Search results

Summary of Contents for PROXIMA PLUS 2011 Series

Reviews:

Related manuals for PROXIMA PLUS 2011 Series

Brands by name

Popular brands