Zetor Proxima 70 2012 Operator'S Manual Download

Page: 162 / 214

161

MAINTENANCE INSTRUCTIONS

E733 G731 G735a

LUBRICATION AND FILLING POINTS
OF THE FRONT DRIVING AXLE

1 - Steering knuckle lubricator.
2 - Sliding bearing (2x) of the front driv-

ing axle.

3 - Gearbox oil drain hole.
4 - Oil filling and inspection hole on the

gearbox (after screwing off the in-
spection screw the oil level shall
reach the lower edge of the inspec-
tion hole).

OIL FILLING, INSPECTION AND
DRAIN HOLES OF FRONT WHEEL
REDUCERS

Carry out check, filling and draining of oil
through one hole after turning the re-
ducer as illustrated.
1. Check of oil level – the hole is in the

reducer horizontal axis (after screw-
ing off the inspection screw the oil
level shall reach the lower edge of
the inspection hole).

2. Filling of oil – the hole is on the top.
3. Drainage of oil from a non-braked

axle – the hole is in the bottom.

4. Drainage of oil from a braked axle –

the hole is in the bottom.

REFILLING OF BRAKE FLUID

The tank is located on the left side of the
tractor in front of the cabin and accessi-
ble after lifting of the bonnet.
Keep level of brake fluid within 3/4 (max.
height) and 1/2 (min. level) of the tank
volume.

When manipulating with brake
fluid observe strict cleanness.

Check level every day before you
drive out.

Summary of Contents for Proxima 70 2012























































































































































































































Search results

Summary of Contents for Proxima 70 2012

Reviews:

Related manuals for Proxima 70 2012

Brands by name

Popular brands

Zetor Proxima 70 2012, Operator'S Manual

Search results

Summary of Contents for Proxima 70 2012

Reviews:

Related manuals for Proxima 70 2012

Brands by name

Popular brands