background image

10 

 

Maintenance and servicing 

 

Cleaning 

If necessary, clean the exterior of the enclosure with a damp cloth. Do not use alcohol or ammonia-based 
liquids to clean the detector. 
 

Servicing 

We recommend the user to periodically inspect the proper triggering of alarm and fault relays, the buzzer 
and indications on the front panel of the controller. Test must be done by applying etalone gas mixture to 
the gas detectors. 
 
 
 
 
The  adjustment operations of the gas detection system must be done only by authorized, trained 
personnel because they may compromise gas detection system reliability. 
 

Servicing frequency 

Zeta Alarms Ltd, recommends regular testing of fixed gas detection installations. The type of test consists 
of injecting a standard gas mixture of sufficient concentration into the detector to set off the preadjusted 
alarms. This test does not, replace a full calibration of the detector. Frequency of the gas testing depends 
on the industrial application in which the detectors are used. Inspection should be done frequently the 
first months after installation starts up, later it may be spaced out if no problem is observed. 
If a detector does not react upon contact with gas, it must be calibrated. The frequency of calibration will 
depend on tests (humidity, temperature, dust, etc.); calibration should occur at least once every year. We 
also recommend calibrating the detector after exposure to high gas concentrations. The site manager is 
responsible for implementing the safety procedures on site. Zeta Alarms Ltd is not responsible for 
implementing safety procedures. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for ZetaGas GS-220.BC.V.ZETA.MET.100













Reviews: