background image

PREMIER AD INSTALLATION MANUAL.  

 

 

Software:PANEL:R1107 & LOOP:R1062 

   

Approved Document No: GLT.MAN-105A

 

 

 

 

PAGE 25

 

Issue : 2.02         Authorised: GH      Date: 16/07/2007 

14. TEST MODE 

 

14.1 WHY USE TEST MODE 

 

To aid commissioning and assist routine maintenance check, a non-latching ‘one man test’ facility is 
available. 

 

When a detector or manual call point is triggered on any zone in Test, the Alarm sounders operate for 
approximately eight seconds on and four seconds off.  This cycle continues until the cause of the 
Alarm is removed (either by the test smoke clearing from the detector or the manual call point being 
reset), sounders will then stop activating. 

 

Should an Alarm occur on a zone that is not programmed to test, the Fire Alarm Panel will cancel the 
test mode. After the cause of the alarm has been checked, and the panel reset, test mode will have 
to be selected again to resume testing. 

 

14.2 TO PROGRAMME ZONE IN TEST MODE 

 

NOTE:  Only 

one zone

 can be programmed in test at any one time. 

 

1.  Insert and turn control key to enabled position; 

 

2.  Press TEST Button. The screen will prompt for the test code 

 

3.  Enter the Test code 

2 4 8.

 

 

4.  The screen will now show Test Mode. 

 

5.  Press TEST FUNCTION SELECT button to select the zone to be  
 tested. 

 

 

6.  Press CONFIRM to enter test mode for this zone 
 

The General Test and Zone Test LEDs will now be lit. 

 

7.  Detectors in this zone can now be tested with smoke spray. The  
 

sounders will operate for about 4 seconds, then they will reset. This 

 

cycle will continue until all smoke spray has cleared from the detector. 

 

8.  Once testing of that zone is completed, press TEST FUNCTION SELECT button to move to 

another Zone or turn the control key switch to off position to exit test mode. 

 

14.3 TO PROGRAM SOUNDER CIRCUITS IN TEST MODE 

 

NOTE:  Only 

one sounder circuit or the loop sounders

 can be in test mode at any one time.  

NOTE:  Only the ADDRESSABLE SOUNDERS can be tested with the loop sounder one man 
test mode. The ASSOCIATED SOUNDER BASES cannot be tested this way because of their 
slower stop/start time.

 

 

1.  Insert and turn control key to enabled position; 

 

2.  Press TEST Button, The screen will prompt for the test code. 
 

Enter the code 2 4 8. 

 

3.  The screen will now show Test Mode, Zone 1, Normal Operation. 

 

4.  Press TEST FUNCTION SELECT button to select the sounder  

 

 

to be tested.  

 

5.  Press confirm to enter test mode for this function. The LED will  
 

now be on steady. 

 

6.  The Sounders will now pulse 3 seconds on, 3 seconds off until  
 

they are taken out of test mode. This allows all the sounders 

 

to be tested for correct operation, and dB output. 

 

7.  Once testing of that sounder circuit is completed, press  
 

TEST FUNCTION SELECT button to move to another circuit, or  

 

turn the control key switch to off position to exit test mode 

 

To test associated sounder bases, use the stop/start sounder button (evacuate). Note that the 
sounders will take up to 9 seconds to start. 

 

***NOTE***Associated sounder bases are controlled by the detector. 

Removing the detector will 

leave the sounder base inoperative. 

     Test Mode 
      Zone  1 

 

  Normal Operation 

 Enter Access Code    

          

  

        

 

     Test Mode 
      Zone  2 

 

    Test Active 

     Test Mode 

      Zone  1 
 

  Normal Operation 

 Enter Access Code    

          

  

        

 

     Test Mode 

 External Sounder 1   
 

    Test Active 

Summary of Contents for Premier AD


































Reviews: