background image

PREMIER AD INSTALLATION MANUAL.  

 

 

Software:PANEL:R1107 & LOOP:R1062 

   

Approved Document No: GLT.MAN-105A

 

 

 

 

PAGE 19

 

Issue : 2.02         Authorised: GH      Date: 16/07/2007 

caps lock as necessary. 

 

10. Press enter when the label has been entered. 
 
 
 
 
11. To skip many addresses, or to change loop, it is  
possible to select the next loop and address to edit.  
Press button 1 or 2 to select the new loop. The Panel  
will then prompt for the address. Type the address and  
press enter. The panel will now jump to this address. 

 

The sounder symbol in the top right hand corner shows that this detector might have 
an “associated sounder base” connected. The panel will send the “activate base 
sounder” command to this address in the event of an alarm. See Sounder section & 
Sounder base setup for further information. 

 

12. When all devices have been entered, press Cancel to exit the message editing 
screen, and cancel again to exit the menu and to return to normal. 

 

The panel is now configured and ready for operation. 

 

12.2 CONFIGURING THE SOUNDER BASES 

 

On the Premier AD, all detectors are treated as if they have a sounder base during 
the initial configuration. If a loop contains a large number of detectors, and a small 
number of sounder bases, then the sounders might take a long time (between 4 & 8 
seconds) to start. 

 

If this scenario exists, it is possible to speed up operation as shown below. (Note: if 
every detector has a sounder base, or if most of the detectors have a sounder base 
this “speed up operation” will have little or no effect. 

 

1. Press enter, NEXT, followed by 369 to enter  
Configuration Menu 2. Select option 5 to edit device status. 
Select a detector that does NOT have a sounder base 
attached. 

 

2. Press the Disablement SELECT button. The sounder 
symbol turns off to show that this detector no longer has  
an associated sounder. (Pressing select again will  
continue to toggle the sounder on & off.) 

 

3. Repeat for all detectors that do not have an associated sounder base fitted. 

 

12.3 SETTING TIME AND DATE 

 

To set the time & date, enter Configuration Menu 2 and select Configure System (6). 
The System Menu is now displayed. Select option 1 to set time & date. Enter the 
Day, Month, Year, Hour & Minutes as prompted, and press enter to save, or Cancel 
at any time to exit. 

 

12.4 SETTING A CUSTOM BANNER 

 

On the Premier AD, the default screen shows Fire alarm Panel to EN54. But this can 
be changed to any 2 lines of 20 Characters that are required. In the System Menu, 
type 

NaMe

 (Caps lock,

N

,Caps lock,

a

,Caps lock,

M

,Caps lock,

e

).  Then type the first 

line of text, followed by enter, then the second line of text, followed by enter. This 
message will now be the screen when the panel is running normally. 

Optical   

           

 

Analog:  25  Normal 

Fl 3 Bedroom 303 

Zone:01  Lp:1 Ad:016 

Optical    

          

 

Analog:  25  Normal 

Fl 3 Bedroom 303 
Zone:01  Lp:1 Ad:016

Optical    

          

 

Analog:  25  Normal 
Fl 3 Bedroom 303 

Zone:01  Lp:1 Ad:016

 Enter Loop Address 

 
     Loop:   1 

  Address: 000 

Summary of Contents for Premier AD


































Reviews: