background image

 

10

 

EC DECLARATION OF CONFORMITY 

Manufacturer: ZERICA s.r.l. 
Address: Zona Industriale – 90018 Termini Imerese (PA) 
Declares under its responsibility that this product: 
 

Complies with the requirements of EEC Directive (2006/95/EC) - low tension directive 
Complies with the requirements of EEC Directive (2004/108/EC - EMC) – electromagnetic compatibility; 
 

Electrical safety: 

 

CEI EN 60335-1 :2013-01 

o

 

Safety of electrical appliances for household and similar use. Part 1: General requirements.. 

 

CEI EN 60335-2-89/2011 

o

 

Electrical appliances for household and similar purposes - Safety. Part 2: Particular requirements for appliances for 

commercial refrigeration condensing unit of refrigerant, compressor or an incorporated or remote 

 

Electromagnetic compatibility: 

 

CEI EN 55014-1/2008+A1-2010+A2-2012 

Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus. Part 1: Emission. 
 

 

CEI EN 55014-2/1998+A1-2002+IS1-2007+A2-2009 

o

 

Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus. Part 2: Immunity. 

 

 

CEI EN 61000-3-2/2007+A1+A2-2011 Part 3-2: 

o

 

Electromagnetic compatibility. Part 3: Limits - Section 2: Limits for harmonic current emissions (equipment input current less 

than 16A per phase).  

 

CEI EN 61000-3-3/2014 

o

 

Electromagnetic compatibility. Part 3: Limits - Section 3: Limitation of voltage fluctuations and flicker in low-voltage supply 

systems for equipment with rated current less than 16A and not subject to conditional connection. 

 

Declares under its responsibility that this product: 

 

Complies  with  Directive  2011/65/CE  (RoHS  2)-  “Restricting  the  use  of  certain  hazardous  substances  in  electrical  and  electronic 

equipment” - RoHS. 

 

The carbonators used by ZERICA S.r.l. have been designed and produced according to sound engineering practice, tested according to the 

reference procedures and are suitable for use in systems for producing sparkling water, using only drinking water and CO2 at a maximum 
operating pressure of 7 bar. 

 

The carbonators are inserted in systems subject to the Machinery Directive (89/392/EC) or the Low Voltage Directive (73/23/EC) and 

therefore do not fall within the scope of the Pressure Equipment Directive - PED (97/23/EC) according to the exclusions in art. 1 point 
3.6. of said Directive. 

 

In addition, the models of carbonators used by Zerica have a product PSxV below the limit established by the PED, at 50, and do not 

therefore have to be CE-marked as they come under the equipment referred to in art. 3§3 in said directive.

 

 

(230)

 

 

 
 
 
 
 
 

 

Summary of Contents for REFRESH P HPDC














Reviews: