background image

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING 

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. 

WARNING 

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 
a.  Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. 

b.  Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.  

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 

CAUTION 

For general ventilating use only. Do not use to exhaust hazardous or explosive materials  and vapors.  Take care when using cleaning agents 

or detergents. Suitable for use in household cooking area. 

WARNING 

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE: 

a.  Never leave surface units unattended at high settings.  Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on 

low or medium settings. 

b.  Always turn hood ON when cooking at high heat or when flaming food   

c.  Clean ventilating fans frequently.  Grease should not be allowed to accumulate on fan or filter. 

d.  Use proper pan size.  Always use cookware appropriate for the size of the surface element. 

e.  Keep fan, filters and grease laden surfaces clean. 

f.  Use high setting on hood only when necessary. 

g.  Don’t leave hood unattended when cooking. 

h.  Always use cookware and utensils appropriate for the type of and amount of food being prepared. 

WARNING 

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING: 

a.  SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. 

 

If the flames do not go out  immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.  

b.  NEVER PICK UP A FLAMING PAN – You may be burned.  

c.  DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d.  Use an extinguisher ONLY if:

1.  You know you have a Class ABC extinguisher, and you already know how to operate it.

2.  The fire is small and contained in the area where it started.

3.  The fire department is being called.

4.  You can fight the fire with your back to an exit

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a.  Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards. Including 

fire-rated construction.

b.  Sufficient air is needed for power combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent 

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire 

Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the 

local code authorities.

c.  When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d.  Ducted fans must always vent to the outdoors.

e.  NEVER place a switch where it can be reached from a tub or shower.

f.  Make sure the power is off before installing, wiring or maintenancing.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages. Not for use over an outdoor grill.

Summary of Contents for Titan Island AK7736AS















































Reviews: