background image

GB-13

G

B

HTZ7500 / CHTZ6000 / CHTZ7500

 WARNING

• Make sure that the engine has stopped and is cool

before performing any service to the machine. Con-
tact with moving cutting head or hot muffler may
result in a personal injury.

AIR FILTER

• The air filter, if clogged, will reduce the engine perfor-

mance. Check and clean the filter element in warm,
soapy water as required. Dry completely before in-
stalling. If the element is broken or shrunk, replace
with a new one.

8. Maintenance

(1)air filter

(1)fuel filter

Every Every Every

25

50

100

       System/components

         Procedure

Before

hours hours hours                   Note

use

after

after

after

fuel leaks, fuel spillage

wipe out

fuel tank, air filter, fuel filter

inspect/clean

replace, if necessary

see adjusting

replace carburetor

idle adjusting screw

idling speed

if necessary

clean and readjust

GAP: 0.6 ~ 0.7 mm

spark plug

plug gap

replace, if necessary

intake air cooling vent

clean

throttle trigger, stop switch

check operation

clean

take it to a service dealer

cutting parts

if somethings wrong

gear case

grease

screws/nuts/bolts

tighten/replace

not adjusting screws

plate receive

make sure to attach

ENGINE

TRIMMER

FUEL FILTER

• When the engine runs short of fuel supply, check the

fuel cap and the fuel filter for blockage.

(1)

SPARK PLUG

• Starting failure and mis-firing are often caused by a

fouled spark plug. Clean the spark plug and check
that the plug gap is in the correct range. For a re-
placement plug, use the correct type specified by
ZENOAH.

0.6~0.7mm

• REPLACEMENT PLUG IS A NGK CMR7H.

Summary of Contents for HTZ7500

















Reviews: