background image

G2500 / G2500 OPS

GB-3

G

B

Contents

1.

For Safe Operation ................................................................... 4

2.

Explanation of Symbols on the Machine .................................. 8

3.

Installing Guide Bar and Saw Chain ......................................... 9

4.

Fuel and Chain Oil .................................................................. 10

5.

Operating the Engine ............................................................. 11

6.

Sawing .................................................................................... 13

7.

Maintenance ........................................................................... 15

8.

Maintenance of Saw Chain and Guide Bar ............................ 16

9.

Troubleshooting Guide ........................................................... 17

10.

Disposal ..............................................................................................

17

11.

Specifications ......................................................................... 18

   12.

Limited Warranty ..................................................................... 19

Masahiko GOUDA
General Manager, Quality Assurance Department

Signed in Saitama, Japan

DECLARATION OF CONFORMITY TO MACHINES DIRECTIVE

(Directive 98/37/EC, 89/336/EEC)
and to the regulations governing transposition
Internal control production

MANUFACTURER : ZENOAH CO.,LTD

No. 9, 1-Chome
MINAMIDAI, KAWAGOE City
SAITAMA, JAPAN

DECLARES THAT THE DESIGN OF THE MACHINE DESCRIBED BELOW :

Model

:  G2500 OPS

Serial no.

: 510001 and up

Make

: ZENOAH

1st April 2007

Masahiko GOUDA
General Manager, Quality Assurance Department

Signed in Saitama, Japan

DECLARATION OF CONFORMITY TO MACHINES DIRECTIVE

(Directive 98/37/EC, 89/336/EEC)
and to the regulations governing transposition
Internal control production

MANUFACTURER : ZENOAH  CO.,LTD

No. 9, 1-Chome
MINAMIDAI, KAWAGOE City
SAITAMA, JAPAN

DECLARES THAT THE DESIGN OF THE MACHINE DESCRIBED BELOW :

Model

:  G2500

Serial no.

: 110001 and up

Make

: ZENOAH

CONFORMS TO THE REQUIRMENTS OF THE MODIFIED MACHINES
DIRECTIVE (Directive 98/37/EC) AND TO THE NATIONAL REGULATIONS
GOVERNING ITS TRANSPOSITION ABROAD : AND

THAT IT HAS BEEN ISSUED WITH A “CE” CERTIFICATE,
NO. M. 0303. 02. 2737
BY THE ISTITUTO CERTIFICAZIONE EUROPEA PALAZZO DEL VESCOVO - V.
GARIBALDI, 20 40011 ANZOLA DELL’ EMILIA - ITALY

1st April 2007

CONFORMS TO THE REQUIRMENTS OF THE MODIFIED MACHINES
DIRECTIVE (Directive 98/37/EC) AND TO THE NATIONAL REGULATIONS
GOVERNING ITS TRANSPOSITION ABROAD : AND

THAT IT HAS BEEN ISSUED WITH A “CE” CERTIFICATE, NO. U3 2592658 01
BY TÜV Rheinland Group - TÜV Rheinland InterCert kft. Product Certification -
H-1061 Budapest Paulay Ede u. 52 - HUNGARY

Summary of Contents for G2500




















Reviews: