background image

20

English

6. MAINTENANCE 

F15

F16

F17

FUEL FILTER (F15)

When the engine runs short of fuel
supply, check the fuel strainer for
blockage.

WAY OF THE COOLING AIR (F16)

This engine is air-cooled. Dust
clogging between the inlet port of the
cooling air and cylinder fins will
cause overheating of the engine.
Periodically check and clean the
cylinder fins after removing the air
cleaner and the cylinder cover.

SPARK PLUG (F17)

Starting failure and mis-firing are
often caused by a fouled spark plug.
Periodically clean the spark plug, and
replace with a new one as required.

When dismounting the plug cap, be
careful not to take off the seal from
the plug cap. Operating the engine
without seal may cause overheating
of the engine.

When setting up the spark plug,
screw it by your fingers at first, then
tighten by using special plug wrench.
Over tightening will damage the
cylinder and piston.

Tightening Torque:
15.3 ~ 22.4 N.m (150 ~ 220kgf-cm)

Type of Plug 

Spark Gap 

NGK CMR7H

or

0.6 ~ 0.7 mm

CHAMPION RZ7C

GEARCASE (F18)

Supply multi-purpose grease at every

25 hours of use

.

1. Use a grease pump.
2. Feed grease until it comes out of

the base of blades.(F18-a)

IMPORTANT

IMPORTANT

F18

Summary of Contents for CHTZ6010

























Reviews: