background image

GB-9

BK3420FL-EZ

G

B

6. Set up

WARNING

•  Assemble each part correctly. Wrong assembly 

might cause an accident. 

•  If you cannot do the assembling yourself, consult 

the shop where you bought this product.

  ATTACHING THE SHOULDER STRAP

1.  Pass  the  ring  of  the  shoulder  strap  through  the 

hook(A) and fix it by the bolt securely.

2.  Set the hook(B) of each shoulder strap to the D-rings 

on the frame.

(A) UPPER SIDE
(B) LOWER SIDE
(1) Hook (A)
(2) Bolt
(3) D-ring
(4) Hook (B)

  CONNECTING THE FLEXIBLE SHAFT

1.  Remove the clamping bolt (M5xL10) in the center of 

the  end  of  the  joint,  and  loosen  the  fastening  bolt 
(M5xL10) and the screw (M5xL18) for mounting the 
throttle lever.

2.  Insert  the  main  pipe  into  the  joint  while  turning  it 

clockwise and counterclockwise slightly.

3.  Align the safety-lock hole of the joint with the hole of 

the main pipe, screw the clamping bolt and fasten it 
tightly.

4.  Tighten the fastening bolt of the joint, and fix the main 

pipe firmly.

[Tightening torque] 
4.9 to 7.8 N

m (0.5~0.8 kg

m)

5.  Screw the throttle-lever mounting screw, and fasten 

it tightly.

(1) Screw (M5xL18) 

(5) Throttle lever

(2) Clamping bolt (M5xL10) 

(6) Joint

(3) Safety-lock hole 

(7) Clamping bolt 

(4) Main pipe 

     

(M5xL10)

6.  Stretch the main pipe and the flexible shaft straight, 

thrust the inner shaft into the main pipe while turning 
it by hand, and connect the inner shaft to the shaft 
of the main pipe. Unless the end of the inner shaft 
appears from the flexible shaft, the inner shaft has 
been  correctly  connected  to  the  shaft  of  the  main 
pipe.

(1) Inner shaft

7.  Turn the hole at the end of the flexible shaft upward, 

align  the  square  hole  of  the  clutch  dram  with  the 
direction  of  the  inner  shaft,  and  thrust  the  flexible 
shaft into the clutch housing until you hear a click.

(1) Clutch housing
(2) Clutch dram 

square-hole

(3) Hole

IMPORTANT

After connecting the inner shaft to the shaft of the main 
pipe, try to pull out the flexible shaft by hand to make 
sure the flexible shaft does not come off.

01-BK3420FL-EZ_GB_207_三.indd   9

12.9.21   1:24:14 PM

Summary of Contents for BK3420FL-EZ























Reviews: