background image

Page 26 of 36 

   802253NZ - HydroTap BC, BCHA-AV, AIO, Installation Instructions - Aug 2015 -  V2.01

     Booster Installation

3.2

  

Installation Procedure

 Site requirements

• 

Appliance must only be installed in a frost-free area. Never expose appliance to frost.

• 

The Appliance is designed for wall mounted Installation and must to be installed with water connectors 
facing upwards.

• 

The appliance complies with protection class IP 25.

• 

The 400mm braided hoses supplied with the unit cannot be lengthened.

• 

The 90

°

 elbow hose ends, should be fitted to the inlet and outlet connections on top of the Booster.

• 

The hot water outlet hose must be thermally insulated with the insulation provided.

Tilt Forward

Lift UP

Release

NOTE:

 Remove the backing plate for wall mounting

3.3

 

    To Remove / Install the appliance

1. 

Insert a flat head screwdriver all the way into the lock.

2. 

Gently angle the screwdriver upwards by approximately 10° as shown in the image below. 

3. 

Pull the appliance forwards by approximately 15° as shown. 

4. 

Carefully pull the appliance upwards to complete the removal process. Taking care not to break the 
lower clips

5. 

To install; Place the appliance on the wall bracket and snap into position (See installation below).

Take care 
not to break 
the lower 
clips when 
removing or 
installing the 
Booster

Installation

Summary of Contents for HydroTap G4





































Reviews: