background image

Autoboil - Installation & Operating Instructions - 81355 - May 2012 v1.01 

Page 7 of 12 

Problem Solving

Operating procedures

Tap Operation

Autoboil is fitted with a two-way safety tap.

The tap assembly has two positions, one is the “cup fill” quick return mode. 
This operation is achieved by having the handle with the curved cam at the 
base of the tap handle facing you. When the handle is released this mode 
allows instant water cutoff.

The second mode is “pot fill”, to use this position rotate the handle 180º 
from the “cup fill” side so a flat face cam is showing at the handle base. This 
operation allows a vessel to be filled without holding your hand where it may 
be affected by steam. 

“Pot fill” position

“Cup fill” position

Symptom

Possible Cause

Solution

Fails to dispense water.

Water isolating valve turned off.

Blocked filter, blocked meter tube, 

blocked strainer, jammed ball valve 

assembly, airlock in transfer tube. 

Check water supply valve.

Contact The Zenith Heaters Limited 

service dept.

Water not boiling.

No power.

Faulty thermostat, faulty element,  

faulty cutout, faulty contactor.

Check power supply.

Contact The Zenith Heaters Limited 

service dept.

Runs out of boiling water and fails to 

refill.

Outlet tap drips.

Overflow from vent.

Excessive steam from vent.

Power “on” but no heat.

Overload repeatedly tripping with 

excessive steam.

Overload repeatedly tripping without 

excessive steam.

Internal adjustment.

Contact The Zenith Heaters Limited 

service dept.

Summary of Contents for 04652 Autoboil













Reviews: