background image

see 3 parking light  and BLUE LED flashes.  Cold or Hot Start Main Setting 
is now set to Cold. 

18. 

Press and release 

19. 

You will also hear 1 remote control beep to signify the first button in the 
sequence. 

20. 

Press and release 

21. 

You will hear 2 remote control beeps to signify the second button in the 
sequence. 

22. 

Press and release 

23. 

You will hear 3 remote control beeps to signify the third button press. 

24. 

You will also hear 5 siren chirps and remote control beeps.  You will also 
see 5 parking light  and BLUE LED flashes.  Run time is now set to 25 
minutes. 

Wait until the BLUE LED on the remote control ceases to flash.  You have no 
exited Cold/Hot Start Timer Programming Mode. 
 
 

3.12   Turbo Timer  

      

(Hold Brake Pedal.  Press and release Function Button 4 times and then press 
and release Remote Start Button) 
 
This feature will allow turbocharged or supercharged vehicles to cool down by 
idling the engine for a specified amount of time.  The engine will continue to idle 
after the key is turned to the OFF position.  
 
Zenesis Electronics developed patent-pending ZMATIC Intelligent Turbo Timer 
that allows users to select 4 different settings for Turbo Timer.   
 
There are 4 settings for the Turbo Timer:  OFF (default) 

 ON 

 Auto (Normal) 

 Auto (Extreme). 

 
You can access each setting by going through the process (Hold Brake Pedal. 
Press Function Button 4 times and then press Remote Start Button) each time. 
Each time you press the Button Sequence, the system will cycle to the next 
setting.   Each setting also has siren chirps/parking light flashes & remote control 
beeps/BLUE LED flashes according to the setting.  See table below:  

 

Button(s) 

Duration 

Description 

2 sec 

Temperature Status 

    

Hold Function Button 

for 2 sec 

 Press and 

release Trunk Button 

Paging ON/OFF (101 A/AS) 

 

Hold Function Button 

for 2 sec 

 Press and 

release Unlock Button  

Remote Control Beep Mute 

ON/OFF 

 

Hold Function Button 

2 sec 

 

Press and 

release Lock Button  

Siren Mute ON/OFF (101 A/

AS) 

 

 

Press and release 

Function Button  

 

Press and release 

Lock Button 

Aux 1 

 

Press and release 

Function Button  

 

Press and release 

Unlock Button 

Aux 2 

 

Press and release 

Function Button  

 

Press and release 

Remote Start Button 

Aux 3 

 

Press and release 

Function Button  

 

Press and release 

Trunk Button 

Aux 4 

 

Press and release 

Function Button twice 

 

Press and release 

Lock Button 

Aux 5 

             

Press and release 

Function Button twice 

 

Press and release 

Unlock Button 

Aux 6 

              

Press and release 

Function Button twice 

 

Press and release 

Remote Start Button 

Aux 7 

Summary of Contents for Z-101 A



















Reviews: