background image

CONTENTS 

1.   Introduction

 

 

1.1    System Contents 
1.2    Remote Control Button Layout  
1.3    Remote Control Battery Replacement 
1.4    Remote Control Button Introduction (Primary/Secondary) 
 

2.   Primary Features 

 
       2.1    Door Lock (Arm—101 A/AS Only) 
       2.2    Door Unlock (Disarm—101 A/AS Only) 
       2.3    Arm / Disarm Status (101 A/AS Only) 
       2.4    Vehicle Status  
       2.5    Panic (101 A/AS Only) 
       2.6    Remote Start 
       2.7    Trunk Release  
       2.8    Valet Mode 
       2.9    Remote Control Button Hold                                                                  

  

3.   Secondary Features

 

 

3.1    User Programmable Options 
3.2    Remote Control Registration 
3.3    Remote Start Reservation 
3.4    Temperature Status 
3.5    Paging (101 A/AS Only) 
3.6    Remote Control Beep Mute 
3.7    Siren Mute (101 A/AS Only) 
3.8    Passive Lock (Arm—101 A/AS Only) 
3.9    Safety Relock (Rearm—101 A/AS Only) 
3.10  Ignition Lock 
3.11  Cold Start Timer 
3.12  Turbo Timer 
3.13  Convenience Run 
3.14  Aux Outputs 
3.15  Shock Sensor (101 A/AS Only) 
3.16  Shock Sensor Sensitivity (101 A/AS Only) 
3.16  Shock Sensor ON/OFF (101 A/AS Only) 
3.17  Z-PASS TOUCH  

 
 
6.   Warranty Card 





 
 
 
13 
14 
14 
15 
15 
15 
16 
16 
17 
 
 
 
19 
21 
21 
22 
22 
22 
23 
23 
24 
24 
25 
28 
29 
30 
31 
31 
32 
32 

33 

 

WARRANTY CARD 

 

Use this warranty card for your records.  Please go to www.zenesis 

alarms/warranty to fill out the warranty details.  Visit the link above 

for specific warranty terms and conditions.

 

 
 
 

Model Number 

 

Owner’s Name 

 

Owner’s Address 

 

Owner’s Phone 

 

Date of Purchase 

 

Date of Install 

 

Retailer Name 

 

Retailer Address 

 

Retailer Phone 

 

Installer Name 

 

Installer Address 

 

Installer Phone 

 

Summary of Contents for Z-101 A



















Reviews: