ZenAire MOB30-18HDN1-MQ0W Service Manual Download Page 56

Page: 56 / 94

Maintenance and

Disassembly



Page 52



MOCA30-23HDN1-MQ0W:

Procedure

Illustration

1) Remove the connector for the

compressor (see

CJ_ODU_INV_011).

2) Pull out the two blue wires connected

with the four way valve (see

CJ_ODU_

INV_011).

3) Pull out connectors of the condenser

coil temp. sensor(T3),outdoor ambient
temp. sensor(T4) and discharge temp.
sensor(T5) (see

CJ_ODU_INV_011).

4) Disconnect the electronic expansion

valve wire (see Fig

CJ_ODU_INV_011).

5) Remove the connector for electric

heaters (see Fig

CJ_ODU_INV_011).

6) Remove the connector for the DR and

reactor (see Fig

CJ_ODU_INV_011).

7) Then remove the electronic control box

(see Fig

CJ_ODU_INV_011).

CJ_ODU_INV_011

Note: This section is for reference only. Actual unit appearance may vary.

Reactor

T3, T4, TP

Compressor

4-Way Valve

Electronic Expansion Valve

Heaters

Summary of Contents for MOB30-18HDN1-MQ0W































































































Search results

Summary of Contents for MOB30-18HDN1-MQ0W

Reviews:

Related manuals for MOB30-18HDN1-MQ0W

Brands by name

Popular brands

ZenAire MOB30-18HDN1-MQ0W, Service Manual

Search results

Summary of Contents for MOB30-18HDN1-MQ0W

Reviews:

Related manuals for MOB30-18HDN1-MQ0W

Brands by name

Popular brands