126
ZW-003_v03
PROBLEMS
POSSIBLE CAUSES
REMEDIES
General problems
Soap suds in the tub of the
dishwasher
Improper detergent.
Use only special dishwasher detergents to avoid soap suds If the soap suds do appear, open the
dishwasher and let them evaporate. Add ca. 4.5 liter of water to the tub and start the rapid program
cycle to empty the dishwasher. Repeat the process, if necessary.
Spilled shiner.
Always clean any spilled shiner at once.
Stains inside the tub of the
dishwasher
A detergent with a dye was used.
Make sure you use a dye-free detergent.
White sediment on the
outside surface
Minerals present in hard water.
To clean the inside of the dishwasher use a wet sponge with a detergent for dishwashers – remember
to wear rubber gloves. Never use other cleaning agents than the dishwasher detergents – this will
prevent any foam or soap suds from appearance.
Rusty stains on cutlery
The cutlery is not stainless.
After adding salt the program was not started.
Salt traces were seen during the washing
cycle.
After adding salt to the dishwasher, always start the Rapid program without any dishes in the
dishwasher.
The lid of the softener is not closed tight.
Check the lid. Make sure it is closed tight.
Noise
Clatter inside the
dishwasher
The sprinkler knocks against an object inside
the dishwasher.
Stop the program and reposition the objects that block the sprinkler.
Rattle inside the
dishwasher
The dishes are placed loosely inside the
dishwasher.
Stop the program and reposition the dishes.
Clatter inside the pipes of
the dishwasher
It may be caused by the pipe installation or
diameter.
This has no effect on the dishwasher. In case of doubt, contact a plumber.
Unsatisfactory washing effect
The dishes are not clean
The dishes were not placed properly.
See guidelines in Loading the dishwasher baskets.
The program was not effective enough.
Wybierz bardziej intensywny program. Patrz „Tabela Cykli Zmywania”.
Not enough detergent.
Użyj więcej detergentu lub zmień detergent.
Object block the way for the sprinklers.
Zmień ustawienie naczyń by zraszacze mogły się swobodnie poruszać.
The filter unit on the bottom of of the
dishwasher is not clean or is improperly
installed. It may cause the sprinklers
to block.
Clean and/or properly install the filter unit.
Clean the openings in the sprinklers.
See: Cleaning the sprinklers.
Glass cloudiness
The effect occurs when the water is soft and
there is too much detergent.
The effect will be more satisfactory, if you use less detergent and selecting shorter cycles which work
better with soft water.
Black or grey traces on
plates
Traces of aluminum cutlery touching against
plates.
Use a gentle abrasive agent to remove the smudges.
There is detergent left in
the dispenser
The dishes block the detergent container.
Reload the dishes.
Unsatisfactory drying effect
Dishes do not dry up
Improper loading.
Load the dishes according to the guidelines.
Not enough shiner.
Increase the amount of shiner/refill the shiner.
The dishes were removed too quickly.
Do not remove the dishes right after cleaning. Leave the door slightly open to let the steam out. Start
unloading the dishwasher only when the dishes are warm to the touch. Remove the dishes from the
bottom basket first. This will prevent the dishes from the upper basket from dripping.
An improper program was selected.
In shorter programs the temperature is lower. Thus it decreases the effectiveness of washing. Select
a program with longer washing time.
Low quality cutlery.
Low quality cutlery or dishes cannot be cleaned in the dishwasher.
ERROR CODES
If there is any malfunction, the dishwasher will display an error warning code:
CODES
MEANINGS
POSSIBLE CAUSES
E1
Longer water inflow time.
The water supply tap is off or water supply has stopped – water. pressure is too low
E3
Longer heating time, the selected temperature cannot be met.
Temperature sensor or heater malfunction.
E4
The dishwasher is full.
Too much water was channeled.
E6
Temperature sensor error.
Open circuit or temperature sensor malfunction.
E7
Temperature sensor error.
Short circuit or temperature sensor malfunction.
ATTENTION! If there is a major spillage, before calling our service turn off the
water tap. If there is water in the base due to overload or small leakage, the water
should be removed before restarting the dishwasher.
Downloaded from DishWasher-Manual.com Manuals
