Zelmer ZWP5265AB, User Manual

Page: 35 / 36

35
WP-002_v02
SUGGESTION
Information on the product and
suggestions for its use
●
The appliance is intended for household use only. The
warranty conditions change if the appliance is used in
gastronomic business.
●
Anti-grease filters as well as active-coal filters
should be cleaned or replaced according to the
recommendations of the manufacturer or more often,
if they are intensively used (more than 4 hours a day).
The cooker hood is a class II electrical appliance.
It is equipped with an independent lighting and an extract fan
with three speed settings.
The cooker hood is designed for a permanent installation on
a vertical wall above the gas or electric cooker.
Parts
The cooker hood is composed of the following elements:
1 The hood body equipped with the lighting and fan unit
2 Grease filter
3 A ring enabling to fix to the ventilation grill
4 Lacquered net protecting the fabric filter
Assembly
In order to assemble the cooker hood:
1 Install the cooker hood at an appropriate height (at least
650 mm from the electric cooking plate and at least 700 mm
from a gas cooker).
2 Plug in the appliance.
Installing the cooker hood
1
Mark a vertical line on the wall indicating the center of
the kitchen plate.
2 Dismantle the net protecting the fabric filter.
3 Put the cooker hood housing against the wall with
the marked center on the vertical middle line, keeping the
minimal distance of 650 mm from the surface of the kitchen.
Make sure the housing is leveled.
4 Mark the position of the assembly holes on the wall.
5
Drill the holes marked on the wall using a drill with the
diameter corresponding to the enclosed rawlplugs, insert the
rawlplugs in the holes and fix the cooker hood housing to the
wall.
6 Install the net protecting the fabric filter.
Plug in and operation control
After plugging the appliance in (according to the previously
described requirements), check if the cooker hood lighting
works and if its motor operates correctly.
After installing the cooker hood, the socket should be easily
accessible in order to unplug the appliance.
Setting the operation mode
Setting the extraction operation mode
During the extraction mode, air is extracted to the outside
with a special duct. Remove the coal filters with this setting.
The cooker hood is connected to an opening that extracts
the air to the outside with a stiff or flexible duct with the
diameter of 120 mm and appropriate duct clamps which are
to be purchased in installation materials supply stores. The
installation should be performed by a qualified fitter.
A
B
Make sure that the above instructions have been
understood.
Technical parameters
Features
Hood type
ZWP5265AB, ZWP6266AB
Voltage 230 V ~ 50 Hz
Fan motor 1
Lighting 28 W; max. 40 W
Speed settings 3
Width [cm] 50/60
Depth [cm] 50
Height [cm] 12
Outlet [ø mm] 120
Efficiency – [m
3
/h] Max 320
Energy consumption [W] 138; max. 150
Loudness [dBA] 52
Type of operation Extraction or absorption
Color White
The appliance meets the requirements of the applicable norms.
The appliance is in conformity with the requirements of the
directives:
–
Low voltage appliance (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) – 2004/108/EC.
The appliance was marked by a CE sign on the rating label.
Features
ZELMER cooker hood is used to extract cooking fumes.
It requires to install a duct extracting air to the outside. The
length of the duct (most commonly a tube Ø 120 mm) should
not exceed 4-5 m.
After installing the active-coal filter which is available in the
sales network, the cooker may operate as an odor absorber.
In this case it is not required to install the duct extracting the
air to the outside, however it is recommended to install an
air exhaust fin.