Zelmer ZVC385SA, User Manual

Page: 52 / 56

58
ZVC385-001_v02
24 Brush for collecting pet hair from carpets (type ZVC385SA)
25 Small nozzle
26 Crevice nozzle
27 Small brush
Preparing the vacuum cleaner for
operation
The Clarris Twix vacuum cleaner has two alternative dust
collecting modules which can be selected by the user:
–
The bagless “CYKLON” dust container with the EPA
filter – where the dust is “whirled” and deposited in the
container.
–
The SAFBAG dust bag module – the dust is accumulated
in a disposable bag with high filtration quality.
1 Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2 Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according to
the figure . Retract the brush when vacuuming carpets
(set the switch in “ ”).
6 The vacuum cleaner is equipped with an accessory
compartment. To open the compartment, lift the compartment
lid and pull it downwards.
7
Grab the plug (3) and pull the cord out of the vacuum
cleaner.
While pulling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8
Plug in the appliance.
Before operation make sure that the SAFBAG dust bag module
or the “CYKLON” dust container is installed in the vacuum
cleaner chamber and that all filters are installed in the appliance.
9 Switch on the vacuum cleaner by pressing the “on/off”
button (7) .
10
The vacuum cleaner is equipped with an electronic power
control which allows to gradually adjust the vacuum cleaner
suction power during operation. To adjust the suction power
use the power adjustment buttons (11,9) – to increase the
suction power or – to decrease the suction power. The
suction power setting is indicated by the appropriate number
of lit diodes.
B
The vacuum cleaner will by default begin operation at the high
power. 4 diodes will light on the power level indicator (10) .
The suction power may be adjusted during operation. The
recommended settings are:
Setting 1 – vacuuming curtains
Setting 2 – vacuuming upholstery
Setting 3 – vacuuming carpets
Setting 4 – vacuuming hard floors and crevices
Setting 5 – maximum suction power.
The power may also be adjusted individually depending on
the type of surface, vacuum effectiveness and suction power
of the switchable combination brush.
11 Set the desired power value by pressing the power
adjustment buttons , (11,9) .
SAFBAG dust bag disassembly/assembly
C
1 The vacuum cleaner is equipped with a dust bag full
indicator (8) . When the dust bag full indicator (8) lights
during operation (with the nozzle or the brush lifted above
the cleaned surface) it means that the bag is full and needs
to be replaced. In addition the dust bag full indicator (8) may
activate if the suction hose or the elements attached to the
suction hose are clogged (suction power – level 5).
2 Switch off the vacuum cleaner by pressing the “on/off”
button (7) and unplug the appliance.
3
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
4 Release the upper cover fastening (12) and open the cover.
5 Remove the SAFBAG dust bag module (21) from the
vacuum cleaner chamber
6
Grab the dust bag cover, gently bend it towards the
inside and remove the whole dust bag upwards.
7 Insert the plate of the new dust bag in the tracks of the
SAFBAG dust bag module (21) and slide it until stop. The
direction for inserting the dust bag is indicated by the arrow
on the bag.
8 Slide the SAFBAG dust bag module together with the
installed bag in the tracks located on the side of the vacuum
cleaner chamber. Close the cover by pressing it until you hear
a characteristic click – pay attention not to trap the dust bag.
Do not vacuum without the SAFBAG dust bag
module/the “CYKLON” dust container installed in
the appliance. The lack of the SAFBAG dust bag
module/the “CYKLON” dust container prevents
from locking the upper cover of the appliance.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the SAFBAG dust bag /”CYKLON” dust container full
indicator will lit up,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.