Zelmer ZVC265SP, User Manual

Page: 59 / 60

65
ZVC265-001_v02
8 Place the emptied CYKLON dust container into the
vacuum cleaner. A characteristic click notifies about a proper
installation.
Emptying the CYKLON dust container is necessary, when:
a) the CYKLON dust container full indicator light is on,
b) the vacuum cleaner operates poorly,
c) the CYKLON dust container is full.
End of operation cleaning
and maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (7) .
2 Unplug the appliance.
3
Wind the cord by pressing the cord rewind button (4) .
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4 Disconnect the telescopic tube from the nozzle or brush.
5
Disconnect the telescopic tube from the hose.
6 Press the side button on the end of the hose, then
remove the end of the hose from the inlet hole of the vacuum
cleaner.
7 The vacuum cleaner may be stored in a vertical position
– just place the fastening hook of the combination brush
into the fastening of the combination brush. The hose may
be connected to the vacuum cleaner. Yet it is necessary to
make sure it is not bent to hard during storing time.
Horizontal storage:
–
place the fastening hook of the combination brush into
its fastening placed at the back of the vacuum cleaner,
near the cord exit.
Vertical storage:
–
place the combination brush on the telescopic tube,
–
place the fastening hook on the telescopic tube into the
fastening of the combination brush placed on the bottom
of the vacuum cleaner, near the front wheel.
8 Clean the housing and the chamber of the vacuum
cleaner with a wet cloth (it may be wet with washing agent),
the dry them or wipe them dry.
Do not use abrasive detergents or solvents.
G
OUTLET FILTER
1
In order to replace the outlet filter (12) pick up the
vacuum cleaner handle, then press the fastenings on the
cover of the outlet filter and slide out the cover out of the
vacuum cleaner.
2
Remove the outlet filter frame out of the vacuum cleaner.
3
Remove the outlet filter out of the frame fastenings.
If the outlet filter (12) is dirty, it may be rinsed with running
water. Remember to dry the filter, before its reinstallation.
Due to safety reasons, it is vital never to install
a damp outlet filter.
4
Carefully put the new/rinsed filter onto all frame
fastenings.
●
Place the cover in such a way that the two protrusions
situated in the bottom part of the cover find their way into
the holes in the body of the vacuum cleaner, and then
press the filter cover to snap the fastenings on the body.
A characteristic click notifies about a proper installation.
Always replace a damaged inlet filter only with
a brand new one.
Disassembly/assembly of the “CYKLON”
dust container
The vacuum cleaner is equipped with a removable CYKLON
dust container (a removable segment of the vacuum cleaner)
gathering all pollutants. When the CYKLON dust container is
full, it needs to be emptied.
1
The vacuum cleaner is equipped with a CYKLON dust
container full indicator (6) . When the CYKLON dust container
full indicator (6) lights during operation (with the nozzle or
the brush lifted above the cleaned surface) it means that
the container is full and needs to be emptied. In addition the
CYKLON dust container full indicator (6) may activate if the
suction hose or the elements attached to the suction hose
are clogged.
2 Switch off the vacuum cleaner by pressing the “on/off”
button (7) .
3 Unplug the appliance.
4
Press the side button on the end of the hose, and then
remove the end of the hose from the inlet hole of the vacuum
cleaner.
5
Press the fastening of the CYKLON dust container
(8) and remove the CYKLON dust container (16) from the
vacuum cleaner.
6
Place the CYKLON dust container over a waste bin.
Press the button on the CYKLON dust container and its
contents will fall out into the bin.
7
After emptying the container, snap its bottom shut.
The container must be tightly closed.
Otherwise the dust might enter the vacuum
cleaner chamber and the suction power will be
reduced.
E
F