65
ZVC227-001_v01
10
Handgrip for carrying the CYKLON dust container
11
Bolt – a mechanic controller of suction power
12
Suction hose
13
Telescopic suction tube
14
EPA E10 inlet filter (installed in the CYKLON dust
container)
15
Foam inlet filter (installed in the CYKLON dust container,
in the frame of the EPA E10 outlet filter)
16
CYKLON dust container (a removable part of the vacuum
cleaner)
17
Dust container cone “CYCLONE” (mounted in dust
container “CYCLONE”)
18
Outlet filter “Microfilter” (mounted in a vacuum cleaner)
19
Switch-over nozzle brush
20
Crevice nozzle (ZVC227SF, ZVC227SK)
21
Small brush (ZVC227SK)
22
Small nozzle (ZVC227SF, ZVC227SK)
Before first use
B
1
Put the end of the suction hose to the inlet of the vacuum
cleaner. A characteristic “click” signalizes the hose has been
properly installed.
2
Connect the other end of the hose with the telescopic
suction pipe.
3
Select the needed length of the telescopic suction pipe
by sliding the slider according to the arrow, and pulling out/in
the pipe.
4
Install a nozzle or a brush on the other end of the suction
pipe.
5
Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure
. Retract the brush when vacuuming
carpets (set the switch in “
”).
6
Grab the plug of the cord
(3)
, and pull it out of the
vacuum cleaner.
Technical parameters
The type of the vacuum cleaner and the technical parameters
are indicated on the rating label. Mains protection 16 A.
Does not cause interferences with audio/video devices.
The device meets the requirements of Commission
Regulation (EU) No. 666/2013 on implementing the Directive
of the European Parliament and of the Council 2009/125/EC
with regard to eco-design requirements for vacuum cleaners.
The device complies with the requirements of the
Commission Delegated Regulation (EU) No. 665/2013
supplementing Directive of the European Parliament and of
the Council 2010/30/EU with regard to energy labelling of
vacuum cleaners.
Noise level: 82 dB(A).
Static electricity
In the process of vacuuming of some surfaces in areas of
low air humidity the device may become electrically charged.
It is a natural phenomenon – it does not damage the device,
and it is not considered to be a fault.
In order to minimize the phenomenon, we recommend you to:
●
discharge the device by touching metal items in the room
with the pipe,
●
increase air humidity in the room,
●
use widely available antistatic agents.
Design
A
1
Outlet filter cover
2
Combination brush fastening
3
Plug with the cord
4
ON/OFF button
5
Suction power regulation slider
6
CYKLON dust container fill indicator
7
Cord winder button
8
CYKLON dust container unlocking button
9
Handgrip for carrying the vacuum cleaner
VACUUM CLEANERS TYPES
Design and
accessory
options
Type
Suction power control
CYKLON container fill
indicator
Protection against using the vacuum cleaner without the EP
A E10 inlet filter installed
Inlet filter
Suction pipe
Nozzle brush
Small nozzle
Crevice nozzle
Small brush
1
2
3
4
5
6
7
8
9
10
ZVC227SF
+
+
+
EPA E10
Telescopic
+
+
+
–
ZVC227Sk
+
+
+
EPA E10
Telescopic
+
+
+
+
Summary of Contents for ZVC227SF
Page 63: ...Notes ...
Page 64: ...Notes ...
