63
Appliance features
The vacuum cleaner 919 is intended to pick up dirt from
floors, carpets, ceramic tiles, slots in wood paneling, skirting
boards, heaters. The vacuum cleaner is also used to vacuum
furniture, curtains, to pick up liquids and to wet clean tiles,
floorings, carpets, fitted carpets and upholstery.
Appliance elements
1
Handle
2
Container lid opening button
3
Plug and cord
4
Accessory compartment
5
Pump operation indicator
6
Pump switch
7
ON/OFF button
8
Power adjustment /- (type 919.0)
9
Power level indicator (type 919.0)
10
Cord rewind button
11
Clogged air inlet indicator (type 919.0)
12
Parquet brush (type 919.0)
13
The vacuum cleaner is equipped with only one type of
suction brush (
A
or
B
)
A
Suction-brush
B
Combination brush with small item separator
14
Turbo brush (type 919.0 ST)
15
Small brush
16
Small nozzle
17
Crevice nozzle
18
Telescopic suction tube
19
SAFBAG dust bag
20
Suction hose
21
Dry filtration module with SAFBAG dust bag
22
Water filter module (filtration unit + partition)
23
Cleaning liquid container
24
Spray unit – suction hose handle attachment
25
Large atomizing nozzle
26
Small atomizing nozzle
27
Water pick up nozzle
28
Rubber slat to the large atomizing nozzle
29
Cleaning powder
30
Anti-foam agent
31
Foam filter I
32
Foam filter II
33
Inlet filter
34
Motor filter
35
HEPA outlet filter
Preparing the vacuum cleaner for operation
1
Insert the end of the suction hose to the vacuum cleaner
opening so that the markings on the hose end and on the
vacuum cleaner housing are opposite each other and turn
the hose clockwise to the position .
2
Connect the other end of the hose (handle) with the
telescopic suction tube.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
Use the following nozzles and brushes for traditional
vacuum cleaning with the SAFBAG dust bag and vacuum
cleaning with the use of the water filter module: combination
brush with small item separator, small nozzle, small brush,
crevice nozzle, parquet brush or turbo brush.
6
You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
7
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the figure
.
8
The vacuum cleaner is equipped with an accessory
compartment. The compartment opens/closes with the use
of a slider. To open/close the compartment side the slider
downwards/upwards and take out/ put away the desired
nozzle.
9
Close the lid.
10
Grab the plug
(3)
and pull the cord out of the vacuum
cleaner.
ATTENTION! While pulling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
11
Plug in the appliance.
ATTENTION! Before switching on the vacuum
cleaner with the on/off button (7), make sure that the
appropriate module is installed in the container (see
section C, E, or F).
12
Switch on the vacuum cleaner by pressing the “on/off”
button
(7)
.
In order to prepare the vacuum cleaner for wet operation
additionally:
13
Assemble the spray unit – the suction hose handle
attachment
(24)
.
Attach the hose fastenings to the suction hose and the
●
telescopic suction tube.
14
Attach the end of the hose (sleeve) to the telescopic
suction tube and insert the other end of the hose in the small
B
A
Summary of Contents for Aquawelt 919
Page 37: ...41...
