15
the kettle to have the body base
14
up. Remove two screws
16
and the screw
17
with a
Philips screwdriver. Lift up the body base
14
and next, disconnect the link
13
from the
thermostat
10
and remove the body base
14
with: the lamp cover
15
, the link
13
and the
switch
28
attached, from the body assembly
9
. Squeeze the arms of the link
13
with a
thin flat tongs in the area between the body base
14
and the switch
28
bringing the link
13
to be disconnected from the switch
28
. Bend out two catches of the lamp cover
15
and remove it from the body base
14
. Undo the clamp and remove the lamp from the
light bracket
11
. Disconnect wire connectors of the heating element from the thermostat
10
. With a Philips screwdriver, remove the screw
12
, mounting the light bracket
11
and
the thermostat
10
to the body assembly
9
, and remove the light bracket
17
. Remove
remaining two screws
12
and the thermostat
10
. Open the lid to its vertical position.
Remove four screws
5
with a Philips screwdriver. Remove the lid
1
from the lid cover
4
and take out the lid lock
2
and the lid spring
3
. With a Philips screwdriver, remove two
screws
36
mounting the handle cover
33
to the body assembly
9
. Lever up the screw
cover
35
with a flat screwdriver and take it out from the handle cover
33
. Remove the
screw
34
with a Philips screwdriver. Lever up the handle cover
33
with a flat screwdriver.
Put your fingers into the resulting gap and pull out the handle cover
33
from the handle
31
. Remove the lid cover
4
from the inside of the body assembly
9
. With a Philips
screwdriver, remove two screws
6
mounting the handle
31
to the body assembly
9
.
Grasp the handle
31
with your hand; pull it down bringing it to be disconnected from the
body assembly
9
. Remove the handle lock
7
from the inside of the body assembly
9
.
Take out the water gauge assembly
30
from the sealing rings
29
located in the body
assembly
9
. Remove two sealing rings
29
from the seats of the body assembly
9
. Place
a flat screwdriver into the spout of the body assembly
9
. Hold the filter
8
with your
fingers, from the inside of the body. Bend out the catch located at the top of the filter
8
and remove the filter
8
from the body assembly
9
.
Disassembly of the power base assembly:
Remove three feet
19
from the power base cover
23
. Remove two screws
24
with a
Philips screwdriver and the screw
25
with a spanner head screwdriver and disconnect
the power base
18
from the power base cover
23
. Remove two screws
21
with a Philips
screwdriver, remove the press block
22
and take out the power cord
32
with the
contactor
20
. Disconnect the connectors of the power cord
32
from the contactor
20
.
ASSEMBLY OF THE KETTLE, TYPE 17Z010, 17Z011, 17Z012
The assembly of the kettle, type 17Z010, 17Z011, 17Z012 proceeds in reverse order
than disassembling, special attention should be paid to proper execution of certain
operations:
Before attaching the thermostat to the heating element, clean the thermostat and the
heating element to remove the thermal grease and apply a new layer of Dow Corning
340 thermal grease in these places.
Electrical wiring shall be made strictly according to the wiring diagram (see below),
taking into account that the electric lamp wires, in any case, shall not touch the
heating element.
Before mounting the body base on the body assembly, you shall connect property the
link with the thermostat.
Summary of Contents for 17Z010
Page 3: ...3 RYSUNEK CZAJNIKA TYM 17Z010 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z010...
Page 5: ...5 RYSUNEK CZAJNIKA TYM 17Z011 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z011...
Page 7: ...7 RYSUNEK CZAJNIKA TYM 17Z012 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z012...
