13
CONSTRUCTION OF KETTLE
An electric kettle is a device designed for boiling water. The kettle body is made of
chrome-nickel sheet, whereas the handle, the lid and the base are made of plastic. A
kettle’s operation, its switching on and after the water is boiled, off, are controlled by a
steam thermostat, which ensures safe operation of the kettle. A lamp, installed on the
kettle bottom, comes on when it is switched on. The complete base is a separate
element used to supply power to the kettle. This design facilitates using the kettle,
because filling it up or pouring the water out does not require removing the plug from the
power socket.
DISASSEMBLY OF THE KETTLE
Before starting to work, carefully review the content of this Service Manual and the
User Manual of the kettle.
Repairs should be made only by a properly trained service technician. Any repair
should be made after removing the plug from the power socket.
Disassembly of the kettle, type 17Z010
Disassembly of the kettle body:
Disassembly should be carried out on a table covered with a clean soft cloth,
taking care not to scratch the parts made of plastic. Remove the kettle from the power
base. Using a thin sharp-ended tool, make a hole in the screw cover
9
. Screw in a screw
into this hole. Remove the screw cover
9
from the handle cover
8
by pulling the screw.
Remove the screw
31
with a Philips screwdriver. Lever up the handle cover
8
with a flat
screwdriver bringing the catches to be disengaged and remove the cover from the
handle
7
. Open the lid to its vertical position. Remove two screws
37
with a Philips
screwdriver. Using a flat screwdriver, disconnect the lid handle between the lid support
5
and the lid cover
4
, lever up the lid support
5
and remove it with the lid assembly from
the kettle. Remove the lid support
5
from the lid cover
4
. Remove four screws
38
with a
Philips screwdriver. Remove the lid
1
with the spring
2
and the lid handle
3
from the lid
cover
4
. Push in the lid handle
3
and remove it with the spring
2
from the lid
1
. Remove
the spring
2
from its seat in the lid handle
3
. Using your fingers, bend out five catches
one by one and disconnect the lid ring
6
from the body assembly
22
. Remove the screw
32
and the screw
33
with a Philips screwdriver. Grasp the handle
7
with your hand; pull it
firmly bringing it to be disconnected from the body assembly
22
. Take out the water
gauge assembly
10
from the silicone rings
12
located in the body assembly
22
. Squeeze
the silicone ring
12
with your fingers and push it in inside the body assembly
22
. Proceed
the same way with the second silicone ring
12
, and next, remove these two silicone rings
12
from the body assembly
22
. Remove the steam cap
13
from the pipe located inside
the body assembly
22
. Place a flat screwdriver into the spout of the body assembly
22
.
Hold the filter
14
with your fingers, from the inside of the body. Bend out the catch
located at the top of the filter
14
with a flat screwdriver and remove the filter
14
from the
body assembly
22
. Remove three screws
35
with a Philips screwdriver and take out the
body base
23
with the switch
17
, the link
18
and the lamp cover
15
attached. Holding the
body base
23
with one hand, pull out the switch
17
, with the other hand, to remove it
from the link
18
. Squeeze the link
18
with your fingers bringing it to be disconnected from
the socket of the body base
23
. Bend out two catches of the lamp cover
15
and remove
it from the body base
23
. Undo the clamp and remove the lamp from the neon bracket
19
. Disconnect wire connectors of the heating element from the thermostat
20
. With a
Philips screwdriver, remove the screw
34
, mounting the neon bracket
19
and the
Summary of Contents for 17Z010
Page 3: ...3 RYSUNEK CZAJNIKA TYM 17Z010 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z010...
Page 5: ...5 RYSUNEK CZAJNIKA TYM 17Z011 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z011...
Page 7: ...7 RYSUNEK CZAJNIKA TYM 17Z012 W ROZ O ENIU NA CZ CI EXPLODED DRAWING OF KETTLE TYPE 17Z012...