background image

 
 

 
 

 

 

Safety Notes 

Microscope Illuminator 

Carl Zeiss 

General 

HBO 50 

 

 

M60-2-0014  e    05/2012 

1

 

Safety Notes 

1.1

 

General 

Before attaching and starting up the illuminator, 

carefully read this operating manual. If you 

need additional information, contact Carl Zeiss 
Service or an authorized Carl Zeiss service 

agency. 
 
To ensure reliable and troublefree operation of 

the microscope illuminator, make sure to 
observe the precautions and warnings given in 

this operating manual. 
 
Only use this microscope illuminator on Carl 

Zeiss microscopes. 

For the microscope Axiovert 40 or 25, use the 
HBO 50 with the Cat. No. 423003-9010-000. 

 
Additionally, observe the provided operating 

manual describing the function of the 
ebq 52 ac lamp power supply. 
Particularly observe the safety notes given in this 

operating manual. 
 
For the handling and operation of the burner 

(lamp) of the HBO 50, observe the specifications 

and safety instructions of the lamp 
manufacturers, (e.g. OSRAM). 
 

The HBO 50 illuminator may only be 

used by personnel appropriately 
trained or instructed by Carl Zeiss 

Service! 
 

Only Carl Zeiss Service is allowed to open the 
lamp power supply! 
 
The following warning and information symbols 
are used in this operating manual: 

 

 

WARNING!

 

Non-compliance with this warning message 
may cause personal injury. 

 

CAUTION! 

Dangerous electric voltage. 

  CAUTION! 

Hot surface. 

 

CAUTION! 

Escape of UV radiation.

 

 

CAUTION! 

Before any intervention in the device, 
disconnect the power cable.

 

 

CAUTION!

 

Non-compliance with this safety note may result 
in damage to the equipment. 

NOTE! 

Note to be observed in using the HBO 50 
Microscope Illuminator. 
 
 

Summary of Contents for HBO 50

















Reviews: