background image

All rights reserved

© 2017 Carl Zeiss 3D Automation GmbH

This document, including all figures contained therein, is subject to copyright protection. Any use beyond 
the strict limits of copyright law permission without the permission of the manufacturer is strictly 
prohibited and punishable by law. This applies in particular to reproduction, translation, microfilming, and 
storing or processing by electronic means.

The replication of trade names and such in this document does not justify the assumption that such 
names should, in the sense of trademark and brand protection legislation, be regarded as unused and 
therefore usable by anyone.

Layout, illustration, photos and text: Carl Zeiss 3D Automation GmbH

Printed in Germany 06/2017

Information about the device

Name

FixAssist® XTR

Device type

Probe presetting device for probe systems 

with XTR plate

Product number 

626109-9160-000

Manufacturer

Carl Zeiss 3D Automation GmbH

Carl-Zeiss-Straße 32

73431 Aalen

Germany

Document version

Article no. Document

Version Date

Note

626109-9160-900

1.0

08.06.2017 valid

A new version status will be created if changes are made to the content 
of this document. The previous status will be rendered invalid, and must 
be replaced by the valid document version.

Summary of Contents for FixAssist XTR




















Reviews: