Zeiss CONTURA Operating Instructions Manual Download Page 143

Page: 143 / 158

Care

61211-1310402

CONTURA

9-13

2 Exhaust port; fan and air filter

Remove the filter cover.

Clean or replace the filter mat.

1 Filter cover

2 Filter mat

Place the filter cover again over the outlet port on the control box.

Checking the compressed air filters

The service unit is equipped with at least two filters. The CMM is usually
equipped with a fine filter and an extra fine filter. The filters have to be
checked regularly. The transparent filter caps make it possible to check
the degree of soiling.

Service unit for compressed air supply

1 Filter cap of the fine filter

2 Filter cap of the super-fine filter

3 Unlock device

4 Direction of rotation

5 Direction for removal

Summary of Contents for CONTURA































































































































































Search results

Summary of Contents for CONTURA

Reviews:

Related manuals for CONTURA

Brands by name

Popular brands

Zeiss CONTURA, Operating Instructions Manual

Search results

Summary of Contents for CONTURA

Reviews:

Related manuals for CONTURA

Brands by name

Popular brands