Zehnder Rittling ComfoAir 155 CM Installation Instructions Manual Download Page 5

5

2.2        Positioning

            

2.2.1           The ComfoAir 155 CM unit must be installed horizontally with the fixing brackets provided. 

                  

2.2.2           It is not advisable to install the unit directly above a bedroom or living room ceiling, or in an area that is part of a 

                  living area or bedroom.
                  

2.2.3           Consideration must be given to allow for adequate access for servicing, maintenance and any fault diagnostics 

                  

(See Section 2.5 Access for Maintenance).

                  

2.2.4           The unit can be configured for right and left hand installation at a touch of a button by following the steps within 

                  the Commissioning Wizard 

(See Section 3.1.4 Commissioning Wizard)

and does not require any internal 

                  changes. 

(See Figures overleaf for ducting configuration).

            

2.3        Configuration

            

                  Note: 

To change the handing of the unit, follow the simple steps within the Commissioning Wizard 

(See Section 

                  3.0).

Automatically done for you via software.

                  
                  ComfoAir 155 CM

Right Hand (factory setting)

INTAKE

EXTRACT

SUPPLY

EXHAUST

Left Hand

EXTRACT

INTAKE

EXHAUST

SUPPLY

Summary of Contents for ComfoAir 155 CM





















Reviews: