Zebex Barcode scanner Quick Referenc Manual Download | Manualshive

Page: 19 / 37

background image

How to Scan

There are two ways to scan with this device.



Handheld scanning



Presentation scanning

Handheld scanning

1.

Power on the scanner.

2.

Press the trigger and aim at the barcode as illustrated.

3.

When decoding is successful, the scanner beeps and the LED indicates blue.

Presentation Scanning

1.

Put the scanner into the cradle for presentation scanning.

2.

Move the barcode label approach the scanner scanning zone.

3.

When decoding is successful, the scanner beeps and the LED indicates blue.

18

«
...
17
18
19
20
21
...
»

Summary of Contents for Barcode scanner






































Reviews:

No comments

Related manuals for Barcode scanner

Brand: Hand Held Products Pages: 56

Brand: SATO Pages: 32

FuzzyScan FA460

Brand: Cino Pages: 67

Brand: Barkodes Pages: 9

Brand: Icarus Pages: 13

Brand: EZ Read Pages: 49

Brand: Clas Ohlson Pages: 4

OBID i-scan ID ISC.MR100

Brand: Feig Electronic Pages: 118

Invexs 170 Series

Brand: Nedap Pages: 4

Brand: Roger Pages: 54

Brand: AUDIOLINE Pages: 2

Brand: Sandberg Pages: 12

Brand: Beinteractive Pages: 13

Brand: Invengo Pages: 36

Brand: RealTrace Pages: 56

Brand: Unitech Pages: 2

Brand: SICK Pages: 122

CLV61 DualPort Series

Brand: SICK Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands