ZComax XN-2050 User Manual Download Page 12

Page: 12 / 71

Chapter 2 Hardware Installation Page 4

Chapter 2 Hardware Installation

This chapter describes initial setup of the Wireless Broadband Router.

Product Package

Before installation, make sure that you have the following items:

IEEE 802.11n (Draft 2.0) 2.4GHz Wireless Broadband Router…………………. x 1

Ethernet

Cable……………………………………………………….…..…….….…..x

Power

Adapter………………………………………………………….……….….….x

Product CD ………………………………………………………….……………….x 1

If any of the above items is not included or damaged, please contact your local dealer for support.

System Requirements

Installation of the IEEE 802.11n (Draft 2.0) 2.4GHz Wireless Router requires:

1. An AC power outlet (100~240V, 50~60Hz) which supplies the power for the Access Point.

Please use the power adapter that contain in the package, not to change to use the

one that make up by non-original factory. The supplier is irresponsible when the

product damage if the user use irregular power adapter.

2. A 10/100 Base-T (UTP) Ethernet cable drop.

Note:

Summary of Contents for XN-2050








































































Search results

Summary of Contents for XN-2050

Reviews:

Related manuals for XN-2050

Brands by name

Popular brands

ZComax XN-2050, User Manual

Search results

Summary of Contents for XN-2050

Reviews:

Related manuals for XN-2050

Brands by name

Popular brands