background image

Zaxcom ZMT4 Flex                                                                                                                ZaxNet Menu

 

13 

ZAXNET MENU 

 

ZaxNet Mode 

 

 

 

 

 

This menu sets the mode of the ZaxNet transceiver. 

 

OFF

 - The ZaxNet transceiver is disabled. The ZMT4 Flex will not receive ZaxNet commands or time code and 

it will not send any ZaxNet audio. Please note if ZaxNet mode is set to OFF the several ZaxNet menu items 

will not appear. 

 

RX 

- The ZaxNet transceiver will receive ZaxNet commands and time code. 

This screen will display what ZaxNet data is being received by the ZMT4 Flex. Including total received 

information packets, ZaxNet TC received and remote-control commands received. This information is used 

for debugging purposes. 

 

TX 

- The ZaxNet transceiver will send ZaxNet confidence audio and time code. Please note that in ZHD48 

mode the ZMT4 Flex will not be able to go into transmit mode. 

 

ZaxNet Receive Frequency Set 

This menu will only appear if ZaxNet is set to receive (RX) mode

 

 

 

 

 

The ZaxNet receive frequency is the frequency that the ZMT4 Flex will get its wireless time code and remote-

control commands on. This frequency will need to match the frequency of the corresponding ZaxNet 

transmitter. The ZaxNet transmitter can be a QRX with QIFB, Nomad, TRX900CL or IFB100/200. The ZMT4 Flex 

can also receive ZaxNet time code from another TRX / ZMT4 transmitter or a ZFR recorder that is transmitting 

ZaxNet on this frequency. Please keep in mind that the range will be limited when receiving ZaxNet from a TRX 

or ZFR. 

When the ZMT4 Flex is receiving a valid ZaxNet signal the signal strength will be shown as well as signal 

strength meter that runs vertically on the far-right side of the screen. 

 

ZaxNet Transmit Frequency Set 

This menu will only appear if ZaxNet is set to transmit (TX) mode

 

 

 

 

 

The ZaxNet transmit frequency is the frequency that the ZaxNet transmitter on the ZMT4 Flex will broadcast 

time code and confidence audio on. Please note the ZaxNet transmitted audio is for quality control purposes 

and the expected range will be less than 20 feet. 

 

 

ZAXNET MODE: TX 

 

RX FREQ : 2.403 RX 

SIGNAL : 28 

ZAXNET TX FREQ: 

  2.473 

Summary of Contents for ZMT-421
































Reviews: