background image

 

26 

FCC Notice: 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. The equipment generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following measures: • 
Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • 
Connect the equipment into an outlet on a circuit different from that which the receiver is connected • Consult the 
dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly 
approved by Zaxcom, Inc. could void the user’s authority to operate it. 

 

 

Summary of Contents for RX-12RR



























Reviews: