background image

Problem

Possible cause

Remedy

The hob deactivates.

You put something on the sensor
field 

.

Remove the object from the sensor

field.

Residual heat indicator does not

come on.

The zone is not hot because it oper‐

ated only for a short time or the sen‐

sor is damaged.

If the zone operated sufficiently long to

be hot, speak to an Authorised Service

Centre.

Hob²Hood does not work.

You covered the control panel.

Remove the object from the control

panel.

 

You use a very tall pot which blocks

the signal.

Use a smaller pot, change the cooking

zone or operate the hood manually.

Automatic Heat Up does not op‐

erate.

The zone is hot.

Let the zone become sufficiently cool.

 

The highest heat setting is set.

The highest heat setting has the same

power as the function.

The heat setting changes be‐

tween two levels.

Power management operates.

Refer to "Daily use".

The sensor fields become hot.

The cookware is too large or you put

it too near to the controls.

Put large cookware on the rear zones,

if possible.

 comes on.

Child Safety Device or Lock oper‐

ates.

Refer to "Daily use".

 comes on.

There is no cookware on the zone.

Put cookware on the zone.

 

The cookware does not cover the

cross / square.

Cover the cross / square fully.

 

The cookware is unsuitable.

Use suitable cookware. Refer to "Hints

and tips".

 

The diameter of the bottom of the

cookware is too small for the zone.

Use cookware with correct dimen‐

sions. Refer to "Technical data".

 and a number come on.

There is an error in the hob.

Deactivate the hob and activate it
again after 30 seconds. If 

 comes

on again, disconnect the hob from the

electrical supply. After 30 seconds,

connect the hob again. If the problem

continues, speak to an Authorised

Service Centre.

You can hear a constant beep

noise.

The electrical connection is incor‐

rect.

Disconnect the hob from the electrical

supply. Ask a qualified electrician to

check the installation.

8.2 If you cannot find a solution...

If you cannot find a solution to the problem

yourself, contact your dealer or an

Authorised Service Centre. Give the data

from the rating plate. Give also three digit

letter code for the glass ceramic (it is in the

corner of the glass surface) and an error

message that comes on. Make sure, you

operated the hob correctly. If not the

servicing by a service technician or dealer

will not be free of charge, also during the

warranty period. The information about

guarantee period and Authorised Service

Centres are in the guarantee booklet.

16

ENGLISH

Summary of Contents for ZIFN844K





















Reviews: