background image

3

IMPORTANT SAFETY INFORMATION

These warnings are provided in the interests of your safety. Ensure that you understand them all before
installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of
the meanings of these warnings contact the Customer Care Department.

Installation

Any  installation  work  must  be  undertaken  by  a

qualified electrician or a competent person.

This hood must be installed in accordance with the

installation instructions and all measurements must
be adhered to.

If the cooker hood is installed for use above a gas

appliance then the provision for ventilation must be
in accordance with the Gas Safety Codes of Practice
BS.6172, BS.5440 and BS.6891 (Natural Gas) and
BS.5482 (LP Gas) 1994, the Gas Safety (Installation
& Use) Regulations, the Building Regulations issued
by the Department of the Environment, the Building
standards  (Scotland)  (Consolidated)  Regulations
issued by the Scottish Development Department.

The fan motor of this cooker hood incorporates a cut-

out device which will operate if the cooker hood is
installed  below  the  minimum  height  recommended
under  section  ‘Clearance  Height’,  or  if  the  motor
becomes  overheated.  If  the  cut-out  device  is
activated,  switch  off  the  fan  motor  and  allow  the
cooker  hood  to  cool.  The  cut-out  device  will  reset
itself when the fan motor has cooled significantly.

It is dangerous to alter the specifications or modify

this product in any way.

When installed between adjoining wall cabinets the

wall cabinets must not overhang the hob.

If the room where the hood is to be used contains a

fuel burning appliance such as a central heating boiler
then its flue must be of the room sealed or balanced
flue type.

If other types of flue or appliances are fitted ensure

that there is an adequate supply of air to the room.

The  ducting  system  for  this  appliance  must  not  be

connected to any existing ventilation system which
is being used for any other purpose.

Do not install above a cooker with a high level grill.

Child Safety

This appliance is designed to be operated by adults.
Children  should  not  be  allowed  to  tamper  with  the
controls or play with the appliance.

During Use

This product is for domestic use only.

Never  leave  frying  pans  unattended  during  use  as
over-heated fats and oils might catch fire.

Never do flambé cooking under this cooker hood.

Do not leave naked flames under the hood.

Maintenance and Service

This appliance can be a hazard if the synthetic paper
and  charcoal  filters  are  not  replaced  as
recommended.

Under no circumstances should you attempt to repair
the  appliance  yourself.  Repairs  carried  out  by
inexperienced  persons  may  cause  injury  or  more
serious  malfunction.  Refer  to  your  local  Zanussi
Service Force Centre. Always insist on genuine spare
parts.

Summary of Contents for ZH 280





















Reviews: