background image

• Carefully obey the instructions for electrical

connections. There is the risk of injury from
electrical current.

Disconnect the appliance from the elec-
trical supply, before you do the mainte-
nance work or you clean it.

• The electrical mains terminal is live.

• Make electrical mains terminal free of volt-

age.

• Install correctly to give anti-shock protection.

• A loose and incorrect mains plug and socket

connections can make the terminal become
too hot.

• A qualified electrician must install the clamp-

ing connections correctly.

• Use a strain relief clamp on cable.

• Use the correct mains connection cable and

replace the damaged mains cable with appli-
cable cable. Speak to your local Service
Force Centre.

• The appliance must have the electrical instal-

lation which lets you disconnect the appli-

ance from the mains at all poles with a con-
tact opening width of minimum 3 mm.

• If the fixing bracket is near to the terminal

block, always make sure the connection ca-
ble does not come in contact with the edge
of the bracket.

• You must have correct isolation devices: line

protecting cut-outs, fuses (screw type fuses
removed from the holder), ground leakage
trips and contactors.

Disposal of the appliance

• To prevent the risk of physical injury or dam-

age

– Disconnect the appliance from the power

supply.

– Cut off the mains cable where it connects

with the appliance and discard it.

– Flat the external gas pipes if there are fit-

ted.

– Speak to your local authorised facilities for

disposal of your appliance.

Installation

Warning!

 The following instructions about

installation, connection and maintenance

must be carried out by qualified personnel in
compliance with standards and local
regulations in force.

Gas Connection

Choose fixed connections or use a flexible pipe
in stainless steel in compliance with the regula-
tion in force. If you use flexible metallic pipes,
be careful they do not come in touch with mo-
bile parts or they are not squeezed. Also be
careful when the hob is put together with an
oven.

Important!

 Make sure that the gas supply

pressure of the appliance obeys the
recommended values. The adjustable
connection is fixed to the comprehensive ramp
by means of a threaded nut G 1/2". Screw the
parts without force, adjust the connection in the
necessary direction and tighten everything.

1

2

3

1

End of shaft with nut

2

Washer

3

Elbow

Liquid gas

: use the rubber pipe holder. Always

engage the gasket. Then continue with the gas
connection. The flexible pipe is prepared for ap-
ply when:

– it can not get hot more than room tempera-

ture, higher than 30°C;

4

 

www.zanussi.com

Summary of Contents for ZGO96524

















Reviews: